Cobra Electronics PR 945 operating instructions Using the Mode Button, Recalling Memory Locations

Page 5

A D VA N C E D O P E R AT I O N

ENGLISH

ENGLISHA D VA N C E D O P E R AT I O N

MODE

Button

Using the MODE Button

The MODE button allows you to use and program the various functions of your microTALK® radio. If you press and hold the MODE button, the LCD will cycle through the different functions.

MODE

Recalling Memory Locations

To recall a channel you have stored in a memory location:

1. Press the MODE button until the Memory icon and a

memory location flashes.

MODE

Button

Programming Memory Locations

Your microTALK® radio has ten (10) memory locations (0-9) for storing your most frequently used channels and privacy codes.

To program locations:

1.

Push the MODE button until the Memory icon and the

 

memory location flashes.

2.

Press the CHANNEL SELECT button up or down to select

 

the memory location you wish to change.

Button

CHANNEL

SELECT

Button

2. Select your desired memory location by pushing the

CHANNEL SELECT button up or down.

Your radio will stay at this memory location until you exit Memory Function mode by pressing the LOCK button.

Repeat steps 1 and 2 to recall other memory locations.

Using the Scan Function

Your microTALK® radio can automatically scan main channels (1-22), the privacy codes (00-38) within one main channel, or memory locations.

CHANNEL

SELECT

Button

TALK

Button

LOCK

MODE Button

Button

3.

Press and release the MODE button again. The Memory

 

icon and the main channel number will flash.

4.

Press the CHANNEL SECTECT button to select the main

 

channel you wish to store.

5.

Press the MODE button again to store the main channel

 

in memory and move to privacy code selection. The

 

privacy code number begins flashing and the Memory

 

icon continues to flash.

6.

Press the CHANNEL SELECT button to select the privacy

 

code (00-38) you wish to store.

7.

Press the LOCK button to program your selection.

 

You may also press the TALK button to transmit your

 

selected channel and privacy code, which will be stored

 

into the memory location you are using.

8. a) Press and release the LOCK button to return to

 

Standby mode at your new memory location.

 

b) Press and release the MODE button to save the

 

memory location and proceed to other functions.

(NOTE: To “unprogram” a memory location you programmed previously, select 00 for both the main channel and privacy code in steps 4 through 6.)

MODE

Button

CHANNEL

SELECT

Button

To scan main channels:

1.Press the MODE button until the Scan icon and main channel number flashes.

2.Push the CHANNEL SELECT button up or down and the radio will begin scanning the main channels.

(NOTE: The radio “ignores” privacy codes while scanning main channels.)

3.The radio will continue to scan all main channels and stop if an incoming transmission is detected. The radio will remain on that channel for ten (10) seconds. During that time you can:

a)Press and hold the TALK button and talk. The radio will remain on that channel and return to Standby mode.

b)Push the CHANNEL SELECT button up or down to resume scanning main channels.

c)Press the MODE button to proceed to privacy code scanning (see following page).

If you do not press any button within ten (10) seconds, the radio will automatically resume scanning main channels.

7

8

Page 4 Page 6
Image 5
Page 4 Page 6
Contents FPO Call Button Battery Saver Circuitry Lock Button Product FeaturesUHF FM Frequencies Backlit LCD Display O D U C T F E AT U R E SAuto Battery Save Battery LowSelecting a Channel Selecting a Ctcss Privacy CodeCalling Another Person Using the Lock FunctionTalking to Another Person Listening for a ResponseUsing the Scan Function Using the Mode ButtonRecalling Memory Locations Programming Memory LocationsTo scan privacy codes Roger Beep Confirmation ToneTo turn Roger Beep On or Off To scan memory locationsCall Tone Settings High/Low PowerSignal Strength Meter Keystroke TonesE C I F I C AT I O N S Safety Information for microTALK RadiosC I N F O R M AT I O N Normal PositionS T O M E R a S S I S TA N C E WA R R a N T Y AccessoriesD E R F O R M Ordering From U.SAviso Sonoro DE Frecuencias UHF FMBotón de Llamada Botón de BloqueoEncendido del radio microTALK BateríasSelección del canal Batería con carga bajaPara hablar con otra persona Para llamar a otra personaPara escuchar a la otra persona Iluminación de la pantallaDe una localidad de memoria Para utilizar el botón de ModalidadProgramación de localidades de memoria Uso de datos en localidades de memoria Función de rastreoPara rastrear los códigos de comunicación privada Para rastrear los canales principalesPara rastrear las localidades de memoria Aviso sonoro de cambioOprima el botón de Modalidad para pasar a otras funciones Para encender y apagar el aviso sonoro de cambioPotencia alta y baja Sonido de teclasMedidor de intensidad de señal Diez señales de aviso de llamadaC E N C I a S P E C I F I C a C I O N E S EspañolPedidos en los EE.UU Formularios DE Pedidos Y AccesoriosPara pedidos con tarjeta de crédito Para efectuar pedidos vía InternetImpreso en China Núm. de catálogo 480-056-P CB radios
Top Page Image Contents