321 Studios AVR360 manual Using Zone, Extended front panel menu, Updating firmware via USB

Page 21

Using Zone 2

Zone 2 provides the option for the occupants of the master bedroom, conservatory, kitchen, etc. to view or listen to a different source at a different volume level from the main zone (Zone 1).

Source selection and volume control for Zone 2 is achieved either by using an IR receiver in Zone 2 (see “Zone2controlconnections”onpageE-46)orbyswitching over to Zone 2 control by pressing the front panel zone button or by pressing amp followed by shifT then ok on the remote control. The front panel VFD display indicates that control has been switched to Zone 2.

S T A N D B Y

Z 2

5 0

D O L B Y T R U E H D 5 . 1

 

 

 

 

 

To turn on Zone 2, press the Zone button (or shift+ok) then press the standby power button on the remote control. Press a source select button to select a different source to Zone 1.

F O L L O W Z 1

Z 2

5 0

D O L B Y T R U E H D 5 . 1

 

 

Note that Zone 2 control from within Zone 1 will pass automatically back to Zone 1 control after a few seconds of inactivity.

Zone 2 can also be controlled using a third-party programmable remote control or a home automation system. Please contact your dealer or installer for further details.

Extended front panel menu

Pressing the menu key and holding it for longer than four seconds will bring up the Extended Menu, allowing you to perform the following:

Restore to factory defaults

This option allows you to restore all settings on your AVR360 to the defaults that it left the factory with.

Change remote code

The default RC5 system code the AVR360 responds to is 16. If required, for example due to another device in your system also using this RC5 system code, it can be changed to 19.

Restore secure backup

This option allows you to restore all settings to their state as saved using the ‘Store secure backup’ feature. This option is useful if settings are accidentally changed. It also allows the unit to be returned to the saved state following a firmware update.

Store secure backup

This option allows you to save all the AVR360 settings to a secure area of memory. The settings can be retrieved using the Restore option above.

– Enter PIN

Enter the secure backup PIN using the ', ,, < and > keys on the remote control (do not use the numeric keypad). The default PIN is 1234.

– Change PIN

Allows the PIN to be changed to a number other than the default. Enter the current secure backup PIN using the ', ,, <and > keys on the remote control (do not use the numeric keypad). The default PIN is 1234. After the current PIN has been entered correctly, enter a new PIN as prompted and again to confirm.

– EXIT

Cancel and return to the extended menu.

Updating firmware via USB

The firmware in your AVR360 can be updated using a USB flash drive containing a firmware update file.

English

E-21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents N d b o o k AVR surround amplifier AVR360Safety Important safety instructionsClass II product English Safety information For European CustomersFCC Information for US customers 1. Product Important notice Do not modify this productPage Professional Installation? ContentsDIY setup? WelcomeBefore you Begin… Standby power PowerPlacing the unit Interconnect cablesTrademark acknowledgements FlacMP3 Digital connectors Audio connectorsVideo connectors Speaker connectorsGeneral Hdmi connectorsMaking connections AV, SAT, BD, VCR, PVRComponent/RGB video connectors Zone 2 connectorsDigital audio connectors Analogue pre-amplifier outputs MCH input Analogue audio inputs Front panel AUX inputFront panel Phones socket AV, SAT, BD, VCR, PVR, CDEnglish Satellite receiver Blu-ray Disc Bd / DVD playerCD player BD/SATConnecting an iPod using the Arcam irDock Radio Connectors Aerial connectorsConnecting an aerial Other Connectors Centre Subwoofer SpeakersFront left and right Surround back left and right Surround left and rightUsing external power amplifiers Connecting speakersConnecting subwoofers Bi-Amping the Front Left & Right speakersOperation Switching onOperating your AVR360 Selecting a sourceUsing Zone Extended front panel menuUpdating firmware via USB Front panel Operation CR102 universal remote controller Inserting batteries into the remote controlUsing the remote control Useful information Device Mode / Source keysCode blink-back Controlling other devicesIPod commands AMP AMP Device ModeTUN TUN Device Mode DVD DVD/BD Device ModeNetwork commands AV AV Device Mode SAT SAT Device ModeAVR360 AVR360.SHIFT + Hselects AUX input on Duplicates function of YELlOW key for someVCR VCR Device Mode PVR PVR Device ModeCD CD Device Mode English Speaker types Essential SetupSpeaker Distances Speaker LevelsAuto speaker Setup ProblemsUsing a subwoofer Navigating the setup menu Setup menusTreble Bass Input ConfigGeneral Setup Auto SetupPlii Dimension Plii Centre Width Plii Panorama Spkr Types None speaker not present in your configurationSpkr Distance Spkr LevelsVideo Inputs Video OutputsMode Network Zone SettingsDecoding Modes IntroductionTwo-channel source modes Multi-channel source modes High resolution audio sourcesDecoding modes For Dolby Digital sourcesVolume Leveller SettingsDolby Volume is a sophisticated new Calibration OffsetEnglish Saving and selecting Presets Tuning/Channel SelectionDeleting Presets Tuner OperationSelecting the playback source Network/usb OperationUSB playback Internet radio stationsMulti-room Set up ZoneZone 2 control connections Multi-room connection guide Code Learning Customising CR102Volume punch-through Creating MacrosKey Mover Locking/Unlocking a specific Device Mode Mode MoverTo restore a moved Device Mode key to its original state Copy a key between Device ModesResetting the CR102 Mode key IR punch-throughProblem Check that Wired network Network hardware Switched offSpeakers Or DTS decoding modesContinual improvement policy SpecificationsWorldwide Guarantee Product GuaranteeClaims under guarantee Problems?
Top Page Image Contents