321 Studios AVR360 manual Specifications, Continual improvement policy

Page 54

specifications

Continual improvement policy

Arcam has a policy of continual improvement for its products. This means that designs and specifications are subject to change without notice.

Continuous power output, per channel, 8Ω

2 channels driven, 1kHz, 0.2% THD	90W
2 channels driven, 20Hz—20kHz, <0.02% THD	80W
5 channels driven, 1kHz, 0.2% THD	75W
Residual noise & hum	<0.3mV
Inputs
Line inputs:
Nominal sensitivity	1V, 2V, 4V (user adjustable)
Input impedance	47kΩ
Signal/noise ratio (CCIR, 65W)	100dB
Preamplifier outputs
Nominal output level	1V RMS
Output impedance	560Ω
THD+N (20Hz—20kHz)	-100dB
Video inputs
Component video signal/noise	85dB
Composite video signal/noise	70dB
Headphone output
Maximum output level into 32Ω	2Vrms
Output impedance	<5Ω
General
Mains voltage	220–240V, 50Hz
Power consumption (maximum)	1kW (Thermal dissipation approx. 3400 BTU/hour)
Power consumption (idle, typical)	100W (Thermal dissipation approx. 340 BTU/hour)
Power consumption (standby)	<0.5W
Dimensions	433 x 425 x 171mm
W x D (including speaker terminals) x H (including feet)
Weight (net)	15.5kg
Weight (packed)	20kg
Supplied accessories	Mains lead
	CR102 remote control
	4 x AAA batteries
	Handbook
	DAB aerial
	FM aerial
	AM loop aerial
	Calibration microphone

E&OE

Note: All specification values are typical unless otherwise stated.

E-54

Image 54

Contents AVR360 N d b o o k AVR surround amplifierSafety Important safety instructionsClass II product FCC Information for US customers 1. Product Safety information For European CustomersEnglish Important notice Do not modify this productPage DIY setup? ContentsProfessional Installation? WelcomeBefore you Begin… Placing the unit PowerStandby power Interconnect cablesTrademark acknowledgements FlacMP3 Video connectors Audio connectorsDigital connectors Speaker connectorsMaking connections Hdmi connectorsGeneral AV, SAT, BD, VCR, PVRComponent/RGB video connectors Zone 2 connectorsDigital audio connectors Front panel Phones socket MCH input Analogue audio inputs Front panel AUX inputAnalogue pre-amplifier outputs AV, SAT, BD, VCR, PVR, CDEnglish CD player Blu-ray Disc Bd / DVD playerSatellite receiver BD/SATConnecting an iPod using the Arcam irDock Radio Connectors Aerial connectorsConnecting an aerial Other Connectors Front left and right SpeakersCentre Subwoofer Surround back left and right Surround left and rightConnecting subwoofers Connecting speakersUsing external power amplifiers Bi-Amping the Front Left & Right speakersOperating your AVR360 Switching onOperation Selecting a sourceUsing Zone Extended front panel menuUpdating firmware via USB Front panel Operation CR102 universal remote controller Inserting batteries into the remote controlUsing the remote control Device Mode / Source keys Useful informationControlling other devices Code blink-backAMP AMP Device Mode IPod commandsTUN TUN Device Mode DVD DVD/BD Device ModeNetwork commands AVR360 AVR360.SHIFT + Hselects AUX input on SAT SAT Device ModeAV AV Device Mode Duplicates function of YELlOW key for somePVR PVR Device Mode VCR VCR Device ModeCD CD Device Mode English Speaker Distances Essential SetupSpeaker types Speaker LevelsAuto speaker Setup ProblemsUsing a subwoofer Setup menus Navigating the setup menuInput Config Treble BassGeneral Setup Auto SetupPlii Dimension Plii Centre Width Plii Panorama Spkr Distance None speaker not present in your configurationSpkr Types Spkr LevelsVideo Inputs Video OutputsMode Zone Settings NetworkDecoding Modes IntroductionTwo-channel source modes Decoding modes High resolution audio sourcesMulti-channel source modes For Dolby Digital sourcesDolby Volume is a sophisticated new SettingsVolume Leveller Calibration OffsetEnglish Deleting Presets Tuning/Channel SelectionSaving and selecting Presets Tuner OperationUSB playback Network/usb OperationSelecting the playback source Internet radio stationsMulti-room Set up ZoneZone 2 control connections Multi-room connection guide Customising CR102 Code LearningVolume punch-through Creating MacrosKey Mover To restore a moved Device Mode key to its original state Mode MoverLocking/Unlocking a specific Device Mode Copy a key between Device ModesMode key IR punch-through Resetting the CR102Problem Check that Speakers Switched offWired network Network hardware Or DTS decoding modesSpecifications Continual improvement policyClaims under guarantee Product GuaranteeWorldwide Guarantee Problems?