ADTRAN ISU 2X64 user manual 109

Page 10

Table of Contents

 

Chapter 9. Security and Remote Configuration

73

Security

73

 

Set Password

74

 

Lock Keypad

74

Remote Config

74

 

Cfg. Rmt. Unit

75

 

Set Password

75

 

Lpbk remote 1B

75

 

Lpbk remote 2B

75

Chapter 10. Troubleshooting

77

 

If Self Test Fails

77

 

If The ISU 2x64 Does Not Read Ready

77

 

If the Wrong DTE Port Answers a Call

83

 

If you Cannot Connect Calls

84

Chapter 11. Specifications

 

 

Network Interface

85

 

DTE Interface

85

 

Dialing Selections

85

 

Data Rates (Network)

85

 

Data Rates (DTE)

86

 

B Channel Aggregation

86

 

Rate Adaptation

86

 

Interoperability

86

 

Switch Compatibility

86

 

Display

87

 

Environmental

87

 

Physical

87

 

Power

87

Appendix A. AT Commands

89

Appendix B. Current Status Messages

95

Appendix C. Status Buffer Messages

99

Appendix D. S-Register List

109

Appendix E. Connector Pinouts

119

Appendix F. Ordering ISDN Without IOCs

125

Acronyms

135

Glossary

137

Index

145

iv

ISU 2x64 Dual Port ISDN Service Unit User Manual

61200051L1-1D

Image 10
Contents ISU Dual Port Isdn Service Unit Part NumbersTrademarks Isdn Page Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Software Version DSU 57.6 Async Txinit Txfa TXADD01 Txdeq Tanull TcidSAP Fallback 109 List Figure E-1 EIA-232 Interface 119 List of Tables Viii Isdn Overview Adtran ISUISU 2x64 Rear Panel DTE Indicators Indicator DefinitionISU 2X64 Single Port Operation ISU 2X64 InteroperabilityISU 2x64 Front Panel ISU 2x64 Interoperability Recommended Operating Protocols DTE#2Recommended Operating Modes Call Type Protocol Sync Rates Supported bps AsyncUnderstanding Isdn and the ISU Chapter Isdn Service Isdn Ordering CodesCapability S previously Generic Data M Capability R previously Generic DataI2 previously Generic Data I-1DN B1 previously Generic Data BCapability C previously Generic Data C J3 previously Generic Data J-1DNJ2 previously Generic Data J M5 previously Generic Data M-1DNChapter Installation Network ConnectionDTE Data Connection Maintenance Interface VT 100 Maintenance Help ScreenDial Interface Connection Chapter Operation Menu NavigationFront Panel DTE Indicators Current Status MenuVT 100 Menu Support Getting StartedStatus Buffer Status Screen VT 100 Status ScreenConfiguration Screen VT 100 Configuration ScreenTest Options Chapter TestingVT 100 Test Menu Screen Loopback Protocol Loopback DTELoopback Network Test Menu TreeLoopback Remote Loopback DisableTest Remote Loopback Both DTEs NEBE/FEBESoftware Version Test 2047 BothDial Line Operation Chapter ConfigurationDial Line Menu Tree Setting the Switch Protocol VT 100 Configuration Menu ScreenLCD Configuration Menu Tree =AT&T 5ESSCofiguration Setting the Call Type Setting the Terminal ID Smart Dial StringsSetting the Busy Out Port Setting the Dial Options =CONFIG Dial Options, RS-366 Menu TreeAT Commands Example ATI1 Example ATSS80? Dial Options, V.25 bis Menu Tree =V.25=CONFIG Dial Line, Auto Answer Menu TreeData Bits Menu Tree Bis Async Menu TreeSetting Auto Answer Setting Answer Tone Answer Tone Menu Tree =Dial Line =Netw. optionsConnect Timout Menu Tree Setting Connect TimoutSetting Call Screening Call Screening Menu TreeSBus Termination SBus Termination Menu TreeClock mode Slave/Master Leased Line ServiceLeased Line Menu Tree Limited Distance Modem Applications Channel RateLeased Application with Channel Banks SBus Termination Asynchronous DTE Options Menu Tree DTE Options for Asynchronous and Synchronous OperationSynchronous DTE Options Menu Tree Bit Rate DTR Options Flow Control Menu Tree Data Format Menu TreeAutobaud Transmit Clock Menu TreeSetting Protocol Options Protocol Menu TreeClear Channel Protocol BONDING, Mode 1 Menu Tree =BONDING modeTxdeq DSU 57.6 Async Rate Adaptation Protocols Call Type Rate Adaption Protocols Typical Units SupportedPPP Menu Tree Point-to-Point Protocol PPP VT 100 Dial Options Screen Chapter Dial OptionsFront Panel Dialing Options Dial Menu TreeRedial last # Hang up lineDial number Answer CallQuick Setup Configuration Chapter Quick SetupQuick Setup Menu Tree Quick Setup Data protocol Bonding mode DTE mode Asynchronous Protocol Bonding mode DTE mode Asynchronous Leased Line AT&T 5ESS SecondQuick Setup Security Security Menu TreeRemote Config Menu Tree Set PasswordRemote Config Lock KeypadLpbk remote 1B Cfg. Rmt. UnitLpbk remote 2B Security and Remote Configuration If Self Test Fails Chapter TroubleshootingIf The ISU 2x64 Does Not Read Ready Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting If the Wrong DTE Port Answers a Call Troubleshooting Calls If you Cannot Connect CallsChapter Specifications Only available on part numbers 1200051L5 and 1200051L6 High x 8.75 wide x 11.00 deep, 3 lbs Specifications AT Commands Appendix aCarrier Detect CD Control Line Options DTE Data Type Options 5ESS Isdn U-Interface Operational Mode Options Appendix a AT Commands Appendix B Current Status Messages ISU is receiving its first TEI from the network Unit is ready to make or accept a call DSU 57.6 Async rate adaptation protocol Appendix C Status Buffer Messages Call control error Called number is busy Called number is out of order Facility requested cannot be provided by the network Invalid message, protocol error Bonding negotiation has failed Number dialed has been changed Local DTE invalid S-register setting Phone number dialed does not exist Auto Answer Appendix DRegister List CharacterIs set Number S26.......DTE Rate AdjustLOW Layer Comp DTE DTR DTE CD= Locd DTR= Bisync S52.......SWITCH Type = NEC= Fallback Dial ModeType = PPPSPID1 LOC DTE ModeChannel Rate SPID2 LOCDCE DTE FlowDTE DTE Clock118 Appendix E EIA-232 InterfaceRS-530 InterfaceRS-366 Interface ST-BRJ-45 Dial Line Connector U Interface PINRJ-45 Dial Line Connector S/T Interface Maintenance Connector124 Appendix F Ordering Isdn Without IOCs Isdn Service Ordering Information for the Adtran ISU 127 TEI Local Interface Requirements Local ServicePhysical Interface Deciding What Services to Order Long Distance Service5ESS Custom Line Additional Parameters 5ESS Features DMS Features DMS-100 Protocol Version 1 Line Additional ParametersAfter Service Is Installed Setting UP the ISU 2X64 for a NEW Line134 Acronyms PRI Glossary Asynchronous transmissionCcitt DDS Isdn NT1 TE1 2B+D 144 Index Numerics146 Isdn 123 Txdeq Txfa Txinit 150 Product Support Information
Related manuals
Manual 2 pages 23.27 Kb