ADTRAN ISU 2X64 user manual Figure E-1 EIA-232 Interface 119

Page 12

List of Figures

 

 

Figure 6-20:

Transmit Clock Menu Tree

54

Figure 6-21:

Protocol Menu Tree

55

Figure 6-22:

Protocol BONDING, Mode 1 Menu Tree

57

Figure 6-23:

PPP Menu Tree

61

Figure 7-1:

VT 100 Dial Options Screen

63

Figure 7-2:

Dial Menu Tree

63

Figure 8-1:

Quick Setup Menu Tree

65

Figure 9-1:

Security Menu Tree

73

Figure 9-2:

Remote Config Menu Tree

74

Figure E-1:

EIA-232 Interface

119

Figure E-2:

RS-530 Interface

120

Figure E-3:

V.35 Interface

120

Figure E-4:

RS-366 Interface

121

Figure E-5:

RJ-45 Dial Line Connector U Interface

122

vi

ISU 2x64 Dual Port ISDN Service Unit User Manual

61200051L1-1D

Image 12
Contents ISU Dual Port Isdn Service Unit Part NumbersTrademarks Isdn Page Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Software Version Txinit Txfa TXADD01 Txdeq Tanull Tcid DSU 57.6 AsyncSAP Fallback 109 List Figure E-1 EIA-232 Interface 119 List of Tables Viii Isdn Overview Adtran ISUISU 2x64 Rear Panel DTE Indicators Indicator DefinitionISU 2X64 Interoperability ISU 2X64 Single Port OperationISU 2x64 Front Panel ISU 2x64 Interoperability Recommended Operating Protocols DTE#2Recommended Operating Modes Call Type Protocol Sync Rates Supported bps AsyncUnderstanding Isdn and the ISU Chapter Isdn Service Isdn Ordering CodesCapability S previously Generic Data M Capability R previously Generic DataB1 previously Generic Data B Capability C previously Generic Data CI2 previously Generic Data I-1DN J3 previously Generic Data J-1DNJ2 previously Generic Data J M5 previously Generic Data M-1DNChapter Installation Network ConnectionDTE Data Connection Maintenance Interface VT 100 Maintenance Help ScreenDial Interface Connection Chapter Operation Menu NavigationFront Panel DTE Indicators Current Status MenuVT 100 Menu Support Getting StartedStatus Buffer Status Screen VT 100 Status ScreenConfiguration Screen VT 100 Configuration ScreenChapter Testing Test OptionsVT 100 Test Menu Screen Loopback DTE Loopback NetworkLoopback Protocol Test Menu TreeLoopback Disable Loopback RemoteTest Remote NEBE/FEBE Software VersionLoopback Both DTEs Test 2047 BothChapter Configuration Dial Line OperationDial Line Menu Tree Setting the Switch Protocol VT 100 Configuration Menu ScreenLCD Configuration Menu Tree =AT&T 5ESSCofiguration Setting the Call Type Setting the Terminal ID Smart Dial StringsSetting the Busy Out Port Setting the Dial Options =CONFIG Dial Options, RS-366 Menu TreeAT Commands Example ATI1 Example ATSS80? Dial Options, V.25 bis Menu Tree =V.25=CONFIG Dial Line, Auto Answer Menu TreeData Bits Menu Tree Bis Async Menu TreeSetting Auto Answer Setting Answer Tone Answer Tone Menu Tree =Dial Line =Netw. optionsSetting Connect Timout Setting Call ScreeningConnect Timout Menu Tree Call Screening Menu TreeSBus Termination SBus Termination Menu TreeLeased Line Service Clock mode Slave/MasterLeased Line Menu Tree Channel Rate Limited Distance Modem ApplicationsLeased Application with Channel Banks SBus Termination DTE Options for Asynchronous and Synchronous Operation Asynchronous DTE Options Menu TreeSynchronous DTE Options Menu Tree Bit Rate DTR Options Flow Control Menu Tree Data Format Menu TreeAutobaud Transmit Clock Menu TreeSetting Protocol Options Protocol Menu TreeClear Channel Protocol BONDING, Mode 1 Menu Tree =BONDING modeTxdeq DSU 57.6 Async Rate Adaptation Protocols Call Type Rate Adaption Protocols Typical Units SupportedPPP Menu Tree Point-to-Point Protocol PPP Chapter Dial Options Front Panel Dialing OptionsVT 100 Dial Options Screen Dial Menu TreeHang up line Dial numberRedial last # Answer CallChapter Quick Setup Quick Setup ConfigurationQuick Setup Menu Tree Quick Setup Data protocol Bonding mode DTE mode Asynchronous Protocol Bonding mode DTE mode Asynchronous Leased Line AT&T 5ESS SecondQuick Setup Security Security Menu TreeSet Password Remote ConfigRemote Config Menu Tree Lock KeypadCfg. Rmt. Unit Lpbk remote 1BLpbk remote 2B Security and Remote Configuration Chapter Troubleshooting If Self Test FailsIf The ISU 2x64 Does Not Read Ready Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting If the Wrong DTE Port Answers a Call Troubleshooting Calls If you Cannot Connect CallsChapter Specifications Only available on part numbers 1200051L5 and 1200051L6 High x 8.75 wide x 11.00 deep, 3 lbs Specifications AT Commands Appendix aCarrier Detect CD Control Line Options DTE Data Type Options 5ESS Isdn U-Interface Operational Mode Options Appendix a AT Commands Appendix B Current Status Messages ISU is receiving its first TEI from the network Unit is ready to make or accept a call DSU 57.6 Async rate adaptation protocol Appendix C Status Buffer Messages Call control error Called number is busy Called number is out of order Facility requested cannot be provided by the network Invalid message, protocol error Bonding negotiation has failed Number dialed has been changed Local DTE invalid S-register setting Phone number dialed does not exist Appendix D Register ListAuto Answer CharacterIs set S26.......DTE Rate Adjust NumberLOW Layer Comp DTE CD = LocdDTE DTR DTR= Bisync S52.......SWITCH Type = NECDial Mode Type= Fallback = PPPDTE Mode Channel RateSPID1 LOC SPID2 LOCDTE Flow DTEDCE DTE Clock118 Appendix E EIA-232 InterfaceRS-530 InterfaceRS-366 Interface ST-BRJ-45 Dial Line Connector U Interface PINRJ-45 Dial Line Connector S/T Interface Maintenance Connector124 Appendix F Ordering Isdn Without IOCs Isdn Service Ordering Information for the Adtran ISU 127 TEI Local Service Local Interface RequirementsPhysical Interface Long Distance Service Deciding What Services to Order5ESS Custom Line Additional Parameters 5ESS Features DMS Features DMS-100 Protocol Version 1 Line Additional ParametersAfter Service Is Installed Setting UP the ISU 2X64 for a NEW Line134 Acronyms PRI Glossary Asynchronous transmissionCcitt DDS Isdn NT1 TE1 2B+D 144 Index Numerics146 Isdn 123 Txdeq Txfa Txinit 150 Product Support Information
Related manuals
Manual 2 pages 23.27 Kb