ADTRAN ISU 2X64 user manual Local Interface Requirements, Physical Interface, Local Service

Page 143

Appendix F: Ordering ISDN Without IOCs

LOCAL INTERFACE REQUIREMENTS

Physical Interface

ISDN Basic Rate Interface (BRI) line

U-interface reference point

2B1Q line coding

ISDN service must be provided from one of the following CO switches and protocols:

Switch

Protocol

AT&T 5ESS

Custom (5E6 or later software)

 

National ISDN-1

Northern Telecom DMS-100

BCS-32 or later software (Pvc1)

 

National ISDN-1 (Pvc2)

Siemens EWSD

National ISDN-1

The interface provides the ability to allocate one dynamic (TEI) per phone number.

Local Service

Bearer capabilities:

-Circuit mode voice service for speech and 3.1 kHz audio.

-Circuit mode data service for 56 kbps and 64 kbps unrestricted data.

Two simultaneous calls supported on the interface. Any mix of speech and data bearer capabilities is supported for both bearer channels on incoming and outgoing calls.

Service provided inside the LATA for the bearer capabilities.

Long distance access for the bearer capabilities to and from the long distance providers of choice.

61200051L1-1D

ISU 2x64 Dual Port ISDN Service Unit User Manual

129

Image 143
Contents Part Numbers ISU Dual Port Isdn Service UnitTrademarks Isdn Page Canadian Emissions Requirements Canadian Equipment Limitations Table of Contents Software Version SAP Fallback Txinit Txfa TXADD01 Txdeq Tanull TcidDSU 57.6 Async 109 List Figure E-1 EIA-232 Interface 119 List of Tables Viii Adtran ISU Isdn OverviewISU 2x64 Rear Panel Indicator Definition DTE IndicatorsISU 2x64 Front Panel ISU 2X64 InteroperabilityISU 2X64 Single Port Operation ISU 2x64 Interoperability DTE#2 Recommended Operating ProtocolsCall Type Protocol Sync Rates Supported bps Async Recommended Operating ModesUnderstanding Isdn and the ISU Isdn Ordering Codes Chapter Isdn ServiceCapability R previously Generic Data Capability S previously Generic Data MJ3 previously Generic Data J-1DN B1 previously Generic Data BCapability C previously Generic Data C I2 previously Generic Data I-1DNM5 previously Generic Data M-1DN J2 previously Generic Data JNetwork Connection Chapter InstallationDTE Data Connection VT 100 Maintenance Help Screen Maintenance InterfaceDial Interface Connection Menu Navigation Chapter OperationCurrent Status Menu Front Panel DTE IndicatorsGetting Started VT 100 Menu SupportStatus Buffer VT 100 Status Screen Status ScreenVT 100 Configuration Screen Configuration ScreenVT 100 Test Menu Screen Chapter TestingTest Options Test Menu Tree Loopback DTELoopback Network Loopback ProtocolTest Remote Loopback DisableLoopback Remote Test 2047 Both NEBE/FEBESoftware Version Loopback Both DTEsDial Line Menu Tree Chapter ConfigurationDial Line Operation VT 100 Configuration Menu Screen Setting the Switch Protocol=AT&T 5ESS LCD Configuration Menu TreeCofiguration Setting the Call Type Smart Dial Strings Setting the Terminal IDSetting the Busy Out Port Setting the Dial Options Dial Options, RS-366 Menu Tree =CONFIGAT Commands Example ATI1 Example ATSS80? =V.25 Dial Options, V.25 bis Menu TreeDial Line, Auto Answer Menu Tree =CONFIGBis Async Menu Tree Data Bits Menu TreeSetting Auto Answer Setting Answer Tone =Dial Line =Netw. options Answer Tone Menu TreeCall Screening Menu Tree Setting Connect TimoutSetting Call Screening Connect Timout Menu TreeSBus Termination Menu Tree SBus TerminationLeased Line Menu Tree Leased Line ServiceClock mode Slave/Master Leased Application with Channel Banks Channel RateLimited Distance Modem Applications SBus Termination Synchronous DTE Options Menu Tree DTE Options for Asynchronous and Synchronous OperationAsynchronous DTE Options Menu Tree Bit Rate DTR Options Data Format Menu Tree Flow Control Menu TreeTransmit Clock Menu Tree AutobaudProtocol Menu Tree Setting Protocol OptionsClear Channel =BONDING mode Protocol BONDING, Mode 1 Menu TreeTxdeq DSU 57.6 Async Call Type Rate Adaption Protocols Typical Units Supported Rate Adaptation ProtocolsPPP Menu Tree Point-to-Point Protocol PPP Dial Menu Tree Chapter Dial OptionsFront Panel Dialing Options VT 100 Dial Options ScreenAnswer Call Hang up lineDial number Redial last #Quick Setup Menu Tree Chapter Quick SetupQuick Setup Configuration Quick Setup Data protocol Bonding mode DTE mode Asynchronous Protocol Bonding mode DTE mode Asynchronous Leased Line Second AT&T 5ESSQuick Setup Security Menu Tree SecurityLock Keypad Set PasswordRemote Config Remote Config Menu TreeLpbk remote 2B Cfg. Rmt. UnitLpbk remote 1B Security and Remote Configuration If The ISU 2x64 Does Not Read Ready Chapter TroubleshootingIf Self Test Fails Troubleshooting Troubleshooting Troubleshooting Troubleshooting Troubleshooting If the Wrong DTE Port Answers a Call If you Cannot Connect Calls Troubleshooting CallsChapter Specifications Only available on part numbers 1200051L5 and 1200051L6 High x 8.75 wide x 11.00 deep, 3 lbs Specifications Appendix a AT CommandsCarrier Detect CD Control Line Options DTE Data Type Options 5ESS Isdn U-Interface Operational Mode Options Appendix a AT Commands Appendix B Current Status Messages ISU is receiving its first TEI from the network Unit is ready to make or accept a call DSU 57.6 Async rate adaptation protocol Appendix C Status Buffer Messages Call control error Called number is busy Called number is out of order Facility requested cannot be provided by the network Invalid message, protocol error Bonding negotiation has failed Number dialed has been changed Local DTE invalid S-register setting Phone number dialed does not exist Character Appendix DRegister List Auto AnswerIs set LOW Layer Comp S26.......DTE Rate AdjustNumber DTR DTE CD= Locd DTE DTR= Bisync = NEC S52.......SWITCH Type= PPP Dial ModeType = FallbackSPID2 LOC DTE ModeChannel Rate SPID1 LOCDTE Clock DTE FlowDTE DCE118 EIA-232 Interface Appendix EInterface RS-530ST-B RS-366 InterfacePIN RJ-45 Dial Line Connector U InterfaceMaintenance Connector RJ-45 Dial Line Connector S/T Interface124 Appendix F Ordering Isdn Without IOCs Isdn Service Ordering Information for the Adtran ISU 127 TEI Physical Interface Local ServiceLocal Interface Requirements 5ESS Custom Line Additional Parameters Long Distance ServiceDeciding What Services to Order 5ESS Features DMS-100 Protocol Version 1 Line Additional Parameters DMS FeaturesSetting UP the ISU 2X64 for a NEW Line After Service Is Installed134 Acronyms PRI Asynchronous transmission GlossaryCcitt DDS Isdn NT1 TE1 2B+D 144 Numerics Index146 Isdn 123 Txdeq Txfa Txinit 150 Product Support Information
Related manuals
Manual 2 pages 23.27 Kb