3Com 3CR17451-91, 3CR17450-91 manual Transceiver, Your Switch, Removing an SFP

Page 29

SFP Operation 27

Figure 5 Inserting an SFP Transceiver

Product label

Suitable port on host Switch

5Use an appropriate cable to connect the transceiver to a suitable device.

6Check the LEDs on the front of the Switch to ensure that it is operating correctly. Refer to “LEDs” on page 13 for more information.

Removing an SFP	If you wish to remove the transceiver (it is not necessary to power-down
Transceiver	your Switch):

1Disconnect the cable from the transceiver.

2Move the wire release lever downwards until it is pointing toward you.

3Pull the wire release lever toward you to release the catch mechanism; the transceiver will then easily slide out.

Image 29

Contents SuperStack 3 Switch 3870 Family Getting Started Guide United States Government Legend 3Com Corporation Campus Drive Marlborough MA USAContents Setting UP for Management PIN-OUTS Page About this Guide Convention Description ConventionsIcon Description Documentation documentation RelatedDocumentation Comments To access the online documentation from the CD-ROM3870 SwitchHardware Features Switch Front View Detail Switch1000BASE-T Ports Stack Master LED Color Indicates Port Status/Packet LEDsStacking Status LED Fault LED Power/Self Test LEDColor Indicates Module LEDs Unit LEDView Detail Duplex Mode Feature Switch Port StatusType of Unit Total Units in the Stack Maximum Modules Port Port SpeedDefault Settings Introducing the Superstack 3 Switch Installing the Switch Site Package ContentsChoosing a Suitable To rack-mount your Switch Power lines and fluorescent lighting fixturesSwitch, as shown in Figure Rack-mountingFitting a bracket for rack-mounting Repeat steps 2 and 3 for the other side of the SwitchPowered-up and ready for operation Power-upSwitch SequenceCross-over Cable Straight-through Cable Power System outputSFP Operation Remove the plastic protective cover if fitted Removing an SFP Your SwitchTransceiver Installing the Switch Setting UP for Management Overview Setting UpAutomatic IP Configuration Manual IP ConfigurationSetting UP for Management Pre-requisites Manually Configuring IP InformationSetting Up the Switch with IP Information Connecting the Workstation to the SwitchExample top-level command line interface menu Automatically Configured IPViewing Viewing Automatically Configured IP Information Viewing IP Information via the Console Port Refer to Setting Up Command Line Interface Management on Interface Management Command LineWeb Interface ManagementWhere xxx.xxx.xxx.xxx is the IP address of the Switch Network Using TelnetInterface Setting Up WebChoosing a Browser Over the NetworkPasswords Setting Up SnmpDefault Users Security Device User Modify operation on the web interface User Default Access Level Name PasswordProblem Solving Power/Self Test LED does not light Solving ProblemsOn powering-up, the Power/Self Test LED remains yellow Indicated by LEDsRefer to the list of suggested solutions below ProblemsSolving Hardware Port Status LED is flashing green/yellowUnit fails or Snmp thermal shutdown trap is received Fan failure warning message is receivedIP Addressing Solving Communication ProblemsError message indicating that the SFP transceiver is faulty How do you obtain a registered IP Address? Solving Software Upgrade Problems Problem Solving Safety Information This must be approved for the country where it is used Power Cord Set Japan Important Safety InformationImportant Safety Information Class ’information de Sécurité Importante’information de Sécurité Importante Dispositif Laser De Classe Vorsicht Europe Wichtige SicherheitsinformationenLaser Gerät der Klasse Información de seguridad importanteSchuko Appendix a Safety Information CSA Importanti Informazioni di SicurezzaSolo Regno Ważne informacje o zabezpieczeniach Appendix a Safety Information Laser Produkt Klasa Appendix a Safety Information RJ-45 to 9-pin PC-AT Serial CableNull Modem Cable RJ-45 to RS-232 25-pin RJ-45 Pin Assignments Modem CableRJ-45 to RS-232 25-pin Pin Number 10/100 1000Pin Number 10/100 1000 Appendix B PIN-OUTS Switch 3870 24 Port Switch 3870 48 Port Services Product to Gain Service BenefitsRegister Your PurchaseDownloads Access SoftwareContact Us Telephone TechnicalAustralia 800 678 Philippines US and Canada Telephone Technical Support and Repair Index SFP Page Chapter Index Regulatory Notices