Uniden EXT1265 manual Install the battery pack, Battery use time per charge, Low battery alert

Page 9

B. Install the battery pack

Place the handset on the base unit and charge the battery pack for at least 15-20 hours before plugging the phone line into your phone.

Battery use time (per charge)

From fully charged:

•6 hours continuous use.

•10 days when the handset is in the standby mode.

Low battery alert

If the phone is not in use, “Low Battery” appears on the LCD and none of the keys will operate. If the phone is in use, “Low Battery” flashes and the handset beeps. Complete your conversation as quickly as possible and return the handset to the base unit

for charging.

note

•Use only the Uniden Battery supplied with your phone. Replacement batteries are also available through the Uniden Parts Department (See page 50) or www.uniden.com

•Even when the battery pack is not being used, it will gradually discharge over a long period of time. For optimum performance, be sure to return the handset to the base unit after each telephone call.

•If you must replace the battery pack during a telephone call, complete the replacement of the battery pack within 30 seconds, and you can return to the original call.

G E T T I N G S T A R T E D

G E T T I N G S TA R T E D [ 7 ]

Image 9

Contents Page Page Contents Terminology FeaturesTalk Controls and FunctionsO N T R O L S a N D F U N C T I O N S Checking the Package Contents Setting up the Phone Do the following stepsChoose the best location Install the battery pack Battery use time per chargeLow battery alert Connect the base unit Base setting only Choose the dialing modeStandard wall plate mounting Setting the handset retainer clip for wall mountingDirect wall mounting Setting Caller ID Options When the phone is in the standby mode, press menu Or Cidcw Off depending upon the type of service to whichUse To move the pointer between Auto Talk On or You subscribe PressHandset Ringer Tone Setting Ringer Volume SetupHandset ringer volume setting Base ringer volume settingUse Or ª To select Distinctive On or Distinctive Ringer SetupSelecting a Language Int’cm/select to select. The Language settingTo move the pointer to Language Screen appearsMaking and Receiving Calls From the Handset From the Base Handset On the BaseHandset Off the Base Base Volume Call Waiting Adjusting Earpiece VolumeRedial from Talk Mode Redialing from Standby ModeRedialing a Call Last three phone numbers dialed can be quickly redialedTraveling Out-of-Range From the baseTo call the last number dialed from the base Press talk key Using One Touch Voice Mail Access Programming your Voice Mail Access NumberWith the base Dialing your Voice Mail Service Message Waiting IndicatorDeleting the Voice Mail Number With the handset Press int’cm/select to selectForth/back between characters E M O R Y D I a L I N G Making Calls with Memory Dialing Memory dialing from Standby Mode With the handsetDisplay a Programmed Number while in Memory Location List Memory dialing from Talk ModePress memory . The memory list is displayed To review the details of a memory locationTo select Use To moveTo scroll through Memory locationsEditing a stored name, phone number or distinctive ring Deleting the stored dataPress to move the pointer to Yes When speaking on the base When speaking on the handsetWay Conferencing Press On the base unit To initiate the 3-way conversationIntercom from the base to handset Intercom/Page FeatureIntercom from the handset to base Base. The handset beeps. If no answer, pressChain Dialing Call Transfer FeatureTo transfer from the handset to the base To transfer from the base to the handsetTone Dialing Switch-over Mute BaseSelecting a Different Channel When the Telephone Rings You must subscribe to Caller ID service to use this featureCaller ID When you answer the call, the display changes to Talk Viewing the Caller ID Message ListPress caller id to return to standby When the pointer is at No When the pointer is at YesDeleting Information from the Caller ID List Deleting a Caller ID messageDeleting all Caller ID names/numbers Using the Caller ID ListCalling a party from the Caller ID list Tone sounds and all stored Caller ID messages are deletedStoring Caller ID messages in memory dialing Long Distance calls and Area Code setting/cancellationUsing Caller ID on Call Waiting Service First caller will be put on holdTo return to the first caller, press call waiting again For example Call Waiting Deluxe FeaturesAccessing Advanced Calling Features Press menu . The following screen appearsUse the or ª key or enter Calling features Display Preprogrammed Activation codes Pre-programmed Calling FeaturesCalling features Activation codes Displaying the pre-programmed activation codesDescriptions of calling features Add or edit a service Adding New FeaturesRestore Svc02? Yes Service02 Restored Remove the handset from the base unit Changing the Digital Security CodePress and hold int’cm/page on the base While the handset is emitting the pagingHeadset Installation Changing the Face PlateTo remove the Face plate To attach the Face plate Maintenance Installing the BeltclipPower Failure Battery replacement and handlingSymptom TroubleshootingBattery Information General InformationAC Adapter Information Precautions Installation Considerations K, L IndexMemo At Uniden, we’ll take care of you