Uniden EXT1265 manual Choose the dialing mode, Base setting only

Page 11

D. Choose the dialing mode

Most phone systems use tone dialing, which sends DTMF tones through the phone lines. However, some phone systems still use pulse dialing such as in rural areas. The default setting is tone dialing. Depending on your dialing system, set the mode as follows:

Base setting only

1	Press and hold call waiting until you hear a confirmation tone.
2	To set the dial mode for pulse dialing, press				# . Or to set the dial
	mode for tone dialing, press			. A confirmation tone sounds to

	indicate the setting is complete.

•If you are not sure of your dialing system, set for tone dialing. Make a trial call. If the call connects, leave the setting as is, otherwise set for pulse dialing.

•If your phone system requires pulse dialing and you need to send the DTMF tones for certain situations during a call, you may “switch-over” to tone dialing (refer to “Tone Dialing Switch-over” on page 32).

note

Make sure your battery pack is fully charged before choosing the dial mode.

G E T T I N G S T A R T E D

G E T T I N G S TA R T E D [ 9 ]

Image 11

Contents Page Page Contents Terminology FeaturesTalk Controls and FunctionsO N T R O L S a N D F U N C T I O N S Checking the Package Contents Choose the best location Setting up the PhoneDo the following steps Low battery alert Install the battery packBattery use time per charge Connect the base unit Base setting only Choose the dialing modeStandard wall plate mounting Setting the handset retainer clip for wall mountingDirect wall mounting Setting Caller ID Options You subscribe Press Or Cidcw Off depending upon the type of service to whichWhen the phone is in the standby mode, press menu Use To move the pointer between Auto Talk On orBase ringer volume setting Ringer Volume SetupHandset Ringer Tone Setting Handset ringer volume settingUse Or ª To select Distinctive On or Distinctive Ringer SetupScreen appears Int’cm/select to select. The Language settingSelecting a Language To move the pointer to LanguageHandset Off the Base Making and Receiving CallsFrom the Handset From the Base Handset On the Base Base Volume Call Waiting Adjusting Earpiece VolumeLast three phone numbers dialed can be quickly redialed Redialing from Standby ModeRedial from Talk Mode Redialing a CallTo call the last number dialed from the base Press talk key Traveling Out-of-RangeFrom the base With the base Using One Touch Voice Mail AccessProgramming your Voice Mail Access Number Deleting the Voice Mail Number Dialing your Voice Mail ServiceMessage Waiting Indicator Forth/back between characters With the handsetPress int’cm/select to select E M O R Y D I a L I N G Making Calls with Memory Dialing Memory dialing from Standby Mode With the handsetTo review the details of a memory location Memory dialing from Talk ModeDisplay a Programmed Number while in Memory Location List Press memory . The memory list is displayedMemory locations Use To moveTo select To scroll throughPress to move the pointer to Yes Editing a stored name, phone number or distinctive ringDeleting the stored data Press On the base unit To initiate the 3-way conversation When speaking on the handsetWhen speaking on the base Way ConferencingBase. The handset beeps. If no answer, press Intercom/Page FeatureIntercom from the base to handset Intercom from the handset to baseTo transfer from the base to the handset Call Transfer FeatureChain Dialing To transfer from the handset to the baseSelecting a Different Channel Tone Dialing Switch-overMute Base Caller ID When the Telephone RingsYou must subscribe to Caller ID service to use this feature Press caller id to return to standby When you answer the call, the display changes to TalkViewing the Caller ID Message List Deleting a Caller ID message When the pointer is at YesWhen the pointer is at No Deleting Information from the Caller ID ListTone sounds and all stored Caller ID messages are deleted Using the Caller ID ListDeleting all Caller ID names/numbers Calling a party from the Caller ID listStoring Caller ID messages in memory dialing Long Distance calls and Area Code setting/cancellationTo return to the first caller, press call waiting again Using Caller ID on Call Waiting ServiceFirst caller will be put on hold For example Call Waiting Deluxe FeaturesUse the or ª key or enter Accessing Advanced Calling FeaturesPress menu . The following screen appears Displaying the pre-programmed activation codes Pre-programmed Calling FeaturesCalling features Display Preprogrammed Activation codes Calling features Activation codesDescriptions of calling features Add or edit a service Adding New FeaturesRestore Svc02? Yes Service02 Restored While the handset is emitting the paging Changing the Digital Security CodeRemove the handset from the base unit Press and hold int’cm/page on the baseTo remove the Face plate To attach the Face plate Headset InstallationChanging the Face Plate Maintenance Installing the BeltclipPower Failure Battery replacement and handlingSymptom TroubleshootingAC Adapter Information Battery InformationGeneral Information Precautions Installation Considerations K, L IndexMemo At Uniden, we’ll take care of you