5) Using the Speed Dial Memory
You can store up to ten names and numbers in each handset. You can dial these numbers with just a few key presses.
Note: When editing the speed dial memory, you must press a key within thirty seconds or the phone will return to standby.
Storing a Name and Number in Memory
) With the phone in standby, press [memory].
2)Enter [0] - [9] or use [vol/
/
] and [vol/
/
] to select the speed dial location where you would like to store.
3)Press [select/channel] twice. STORE
NAME appears and a cursor flashes indicating that the phone is ready for the name to be entered.
Note: If the selected speed dial number is already assigned, the Edit screen appears. You can select EDIT MEMORY to edit this entry, select DELETE MEMORY to erase this entry, or select GO BACK to choose another speed dial number.
Select Memory 01ｰ
02 JOHN DOE
Store Name
ｰEdit Memory01
Delete Memory01
Go Back
4)Enter a name (up to thirteen characters) using the keypad. If no name is required, go to step 5.
•Use [
/tone/
] and [#/
] to move the cursor to the desired location.
•Press [delete/transfer] to delete characters as needed.
•If you make a mistake, move the cursor to the incorrect character and erase the wrong character. Then enter the correct character.
•To delete all characters, press and hold [delete/transfer].
•If the next character uses the same number key, press [#/
] first to move the cursor over. Otherwise the next time you press the number key, it changes the character that was previously set.
Refer to the letters on the number keys to select the desired characters. With each press of a number key, the displayed character appears in the order shown the following table.
|
|
| Number of times key is pressed |
|
| ||||
keys | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |
| 1 |
|
|
|
|
|
|
|
|
| A | B | C | a | b | c | 2 |
|
|
| D | E | F | d | e | f | 3 |
|
|
| G | H | I | g | h | i | 4 |
|
|
| J | K | L | j | k | l | 5 |
|
|
| M | N | O | m | n | o | 6 |
|
|
| P | Q | R | S | p | q | r | s | 7 |
| T | U | V | t | u | v | 8 |
|
|
| W | X | Y | Z | w | x | y | z | 9 |
| * | # | - | & | ( | ) | (blank) | 0 |
|
For example, to enter Movies.
1.Press [6] once.
Then press [#/
] to move the cursor to the right.
2.Press [6] six times.
3.Press [8] six times.
4.Press [4] six times.
5.Press [3] five times.
6.Press [7] eight times.
) Press [select/channel]. STORE NUMBER is displayed. The cursor flashes indicating that the phone is ready for the number to be entered.
) Use the keypad to enter the phone number (up to twenty digits). To enter a
•You can also enter multiple pauses. Each pause counts as a digit.
•The display shows a P for every pause.
7)Press [memory]. Memory storage is
complete. | Memory01 Stored |
) After about two seconds, the screen |
|
displays the memory list. |
|
9) Press [end] to exit the memory list. The phone returns to standby.
Storing Caller ID Numbers in Speed Dial Memory
Caller ID names and numbers shown in the Caller ID list can be stored in speed dial memory.
) With the phone in standby, press [cid/menu].
2)Use [vol/
/
] or [vol/
/
] to select the phone number you would like to store.
3)Press [memory].
4)Enter a number ([0] – [9]) or press [vol/
/
] or [vol/
/
] to select the memory location to be stored.
) Press [select/channel] to store the number.
Note: If a number has already been stored in the selected memory location, a confirmation screen is displayed. To overwrite, press [vol/
/
] to select YES and press [select/channel].
) The display returns to the Caller ID list.