Uniden EXAI378 Changing the Digital Security Code, Installing the Beltclip, Headset Installation

Page 55

Changing the Digital Security Code

The digital security code is an identification code used to connect the handset and the base unit. Normally, setting the code is not necessary.

The first time you charge your handset, the security code is automatically set. (See "About the digital security code", page 7.) In the rare situation that you suspect another cordless telephone is using the same security code, you can change the code.

1)Remove the handset from the base unit. Press and hold find hs on the base.

2)While the handset is emitting the paging sound, place the handset on the base unit holding find hs. The paging sound stops. Leave the handset on the base for more than 3 seconds. A new random security code is set.

Installing the Beltclip

To attach the beltclip	To remove the beltclip
Insert the beltclip into the holes on	Pull both sides of the beltclip to
each side of the handset. Press down	release the tabs from the holes.
until it clicks.
Headset Installation

Your phone may be used with an optional headset, the Uniden HS910. To use this feature, insert headset plug into the headset jack. Your phone is ready for hands-free conversations.

(Headset may be purchased by calling the Uniden Parts Department or visiting the web site. See Page 8.)

If the handset battery pack is completely discharged or the battery pack is removed, the digital security code will be lost. If this happens, a new security code is set automatically next time the battery pack is charged.

INFORMATION

ADDITIONAL

A D D I T I O N A L I N F O R M AT I O N [ 53 ]

Image 55

Contents Page Page Contents Color of your cordless phone may vary Page Charging the Battery Controls and Functions O N T R O L S a N D F U N C T I O N S About the digital security code Read this First10 to 38 toChecking the Package Contents Do the following steps Setting up the PhoneChoose the best location E T T I N G S TA R T E D Low battery alert Battery use time per chargeCleaning the battery charging contacts Connect the base unit Standard wall plate mounting Mounting the Base Unit on a WallDirect wall mounting TerminologyCaller ID options Setting Menu OptionsPage Setting the language Choosing the dial modeHandset On Base Handset Off Base Making and Receiving CallsEarpiece volume Handset ringer tone and volumeRinger Mute Redial Tone Dialing Switch-overTraveling Out-of-Range Flash and Call Waiting Selecting a Different ChannelStoring Phone Numbers and Names Memory Dialing If you make a mistake while entering a name Steps for Entering Names and Special CharactersNumber of times key is pressed Integrated Answering Device Memory Dialing Making Calls with Memory Dialing Memory dialing from Standby ModeDisplay a programmed number Chain Dialing Memory dialing from Talk ModeEditing a Stored Name and/or Phone Number Memory 1 Stored Memory Store 7Press select or delete/ch Erasing a Stored Name and Phone NumberStoring and Editing the RocketDial RocketDialMaking calls with the RocketDial 5Press select or delete/ch Deleting the RocketDialYou must subscribe to Caller ID service to use this feature When the Telephone RingsCaller ID Viewing the Caller ID Message List Deleting a Caller ID message When the pointer is at YesWhen the pointer is at No Deleting Information from the Caller ID ListDial edit Using the Caller ID ListLong Distance calls and Area Code Setting/Cancellation Calling a party from the Caller ID listStoring Caller ID messages in Memory dialing Integrated Answering Device FeaturesUsing the Menu Mode Setting up Your Answering SystemTurning the Answering System On/Off Setting the Time Setting a Personal Security Code PIN Setting the ring time Selecting the message record time Announce only featureSetting the Message Alert tone Preset message Setting Your Outgoing Message GreetingChoosing between the two outgoing messages Adjusting the speaker volume level Setting the base ringer volumePlaying your messages Using Your Answering SystemSkipping a message Repeating a messageDeleting a message During recording Voice memoRecording a conversation Beep that can be heard by both parties, soundsCommand Remote access away from homeTurn on the answering system remotely To attach the beltclip To remove the beltclip Installing the BeltclipHeadset Installation Changing the Digital Security CodeMaintenance Symptom Suggestion TroubleshootingD D I T I O N a L I N F O R M a T I O N Symptom Suggestion General Information Battery InformationAC Adapter Information Precautions Installation Considerations Terminal Equipment Radio Equipment G, H, I, J, K, L IndexCall your phone number from a touch-tone phone Remote Operation CardTask Key Please do not Return this Product to the Place of Purchase At Uniden, we’ll take care of you