Uniden TRU 8880 owner manual Function

Page 73

4)Enter a command within 15 seconds; each command there after must be entered within 2 seconds. You may select a command from the following chart:

Command	Function	Command	Function

0 then 1	Repeat a Message*	0 then 6	Answering System On
0 then 2	Playing incoming Messages	0 then 7	Memo Record/Stop**
0 then 3	Skipping a Message	0 then 8	Greeting Message Record/Stop**
0 then 4	Deleting a Message	0 then 9	Answering System Off
0 then 5	Stop Operation	1 then 0	Help

*For the Repeat a Message function, press 0 then 1 within about four seconds to repeat the previous message, or press 0 then 1 after about four seconds to repeat the current message.

**For the Memo Record and Greeting Message Record function, the first time you enter the corresponding command, it starts the Recording function. If you want

to stop the recording, press 0 then 7, 8 or 5.

5)After the command has finished, you hear intermittent beeps indicating that the system is in the command waiting mode. You may enter another command at this time from the chart above.

6)When you are finished, hang up to exit the system. The answering system automatically returns to standby.

note

•Time stamp will not be heard until you have set the time. See "Setting Day and Time" on page 29 or 60.

•The system will only playback messages for four minutes and then it returns to the command waiting mode. To continue playing your messages, press 0 then 2 again within 15 seconds.

•If you enter an incorrect PIN code three times, you will hear a beep and the system will return to standby.

•During the remote operation, Line Remote appears on the display.

•If the answering system is recording an incoming message, the recording operation is cancelled when you start remote operation.

•For your convenience a remote operation card is provided for you to use while away from home (refer to page 92).

T H E I N T E G R A T E D A N S W E R I N G D E V I C E

w w w . u n i d e n . c o m

T H E I N T E G R A T E D A N S W E R I N G D E V I C E [ 7 1 ]

Image 73

Contents Series Owners Manual Page Contents Welcome Features Terminology Handset Antenna Play/stop P Find hs/intercom P Display and Icons Example of the standby mode displayMaking a call Animation DisplaysTalk mode Standby modeSoft Key Function Do the following steps Setting up the PhoneInstall the rechargeable battery pack into the handset Connect the base unit Standard wall plate mounting Mounting the Base Unit on a WallDirect wall mounting Expanding Your Phone Connecting the ChargerHandset Expandability Register the Handset Main Menu Options Default SettingsUsing the interface Setting Menu OptionsUsing DirectLink Mode DirectLink ModeRoom/Baby Monitor Using Room/Baby MonitorSelecting a Ringer Tone Handset SetupPress Distinctive Ringer SetupVol/∨ to select On or Off Press the OK soft key. You will hear a confirmation toneSetting the Anykey Answer Setting the AutoTalkSelecting a Language Setting the True BannerVol/ ∨ to choose English Français French, or Español SpanishPress /vol/∧ or /vol/∨ to adjust the contrast LCD 10 levels Adjusting the LCD ContrastSetting the Key Touch Tone Menu and then the Contrast submenuAnswering System Setup Setting the Animation ScreenSetting a PIN Code Available screensSetting the Record Time Setting the Ring TimeTurning the message alert tone off by pressing any key Setting the Message Alert On or OffTurning the message alert tone off from a remote location Setting the Call Screen Setting the Language of your Answering SystemFrench, or Español Spanish Setting Day and Time Global SetupSetting the Area Code Setting Cidcw Caller ID on Call WaitingOK soft key. You will hear a confirmation tone Then the Dial Mode submenu Setting the Dial ModeInitial setting is Tone Press /vol/ ∧ or /vol/ ∨ to select Tone or PulseDe-register the Handset 6CNM Making and Receiving CallsFrom the Base Receiving calls only From the handsetPress speaker and begin speaking To hang up, press speaker Placing a Call on Hold Call WaitingDeleting a Redial Record Redialing a CallStoring a Redial Record Ringer volume Adjusting the Ringer, and Earpiece and Speaker VolumeEarpiece and Speaker Volume Do Not Disturb DND Muting the RingerTemporarily Muting the Ringer Mute Microphone Tone Dialing Switch-overWith the handset With the baseWorks only when the phone is in use Privacy ModeVol/ ∨ to move the pointer to Privacy Mode and then Travelling Out of RangeWay Conferencing ConferencingPress the Store soft key, Store/Edit Name appears Vol/∧ or /vol/∨Chain Dialing If you make a mistake while entering a name Steps for Entering Names and Special CharactersFor example, to enter Movies Press /vol/ ∧ Vol/ ∨ , or the number keypad to Viewing the PhonebookFrom Standby Mode Making Calls Using the PhonebookFrom Talk Mode Speed DialingVol/∨ to move the pointer to If you select All Memories, Are you sure? appears on Copying Phonebook LocationsOr the number key 2-9and 0 to select the phonebook Location you want to export and then press the CopyCaller ID and Cidcw Caller ID on Call Waiting Press cid Viewing the Caller ID ListDeleting Information from the Caller ID List Deleting a Caller ID MessageVol/∨ to choose Yes Deleting all Caller ID names/numbers Using the Caller ID Message ListCalling a party from the Caller ID list Press /vol/∧ or /vol/∨ to choose YesStoring Caller ID messages in the Phonebook Talk mode%QPHGTGPEG &TQR.CUV Call Waiting Deluxe FeaturesIntegrated Telephone Answering Device FeaturesTurning the Answering System On/Off Answering System Default SettingsSetting up your Answering System Answering System Settings Press set to select the hour Setting the TimeSetting the ring time Setting a PIN codeSelecting the message record time Announce only featureTurning the message alert tone off by pressing any key Setting the message alertCall screen Selecting the languageFrom the handset Screening a callFrom the base When the phone is in standby mode, press play/stop Using your Answering SystemPlaying your messages Skipping a message Repeating a messageVoice memo Deleting a messageRecording a conversation Remote Operation Remote access away from homeFunction Remote access with the handset †/5 Remote Key FunctionUsing the DirectLink Mode Multi-Handset FeaturesDirectLink call Intercom Intercom/Call Transfer FeatureFrom handset to handset or handset to the base Standby mode, press intcom/holdFrom the base to a handset Call Transfer FeatureFrom handset to handset or to the base From the base to a handset Headset Installation Installing the BeltclipChanging the Digital Security Code To attach the beltclipPower Failure Battery replacement and handlingCleaning the battery charging contacts Low battery alertGeneral Information Battery InformationAC Adapter Information Symptom Suggestion TroubleshootingSevere noise interference Symptom Suggestion Case Action Liquid DamagePrecautions Installation Considerations Terminal Equipment Memory List Memo G, H IndexRemote Operation Card Remote access away from homeTask From standby mode Main Menu Flow ChartI N M E N U F L O W C H a R T 9 Please do not Return this Product to the Place of Purchase Page Register Online Today