Sharp DK-KP85PH operation manual Enhancing your system, Troubleshooting chart

Timer and sleep operation (Remote control only) (continued)

■■ Sleep operation

The radio, compact disc, iPod, USB, Audio In can all be turned off automatically.

1Play back the desired sound source.

2 Press the SLEEP button.

3 Within 5 seconds, press the Numeric buttons to set the time. (1 minute ~ 99 minutes)

4 “SLEEP” will appear.

5 The unit will enter the power stand-by mode automatically after the preset time has elapsed. The volume will be turned down 1 minute before the sleep operation finishes.

To confirm the remaining sleep time:

While “SLEEP” is indicated, press the SLEEP button.

To cancel the sleep operation:

Press the ON/STAND-BY button while “SLEEP” is indicated. To cancel the sleep operation without setting the unit to the stand-by mode, proceed as follows.

1While “SLEEP” is indicated, press the SLEEP button.

2 Within 5 seconds, press the “0” button twice until “SLEEP 00” appears.

■■ To use timer and sleep operation together

Sleep and timer playback:

For example, you can fall asleep listening to the radio and wake up to CD in the next morning.

1	Set the sleep time (see above, steps 1 - 5).
2	While the sleep timer is set, set the timer playback
	(steps 2 - 9, page 21).
Sleep timer		Timer playback	End time
setting		setting

Enhancing your system (continued)

2Press the ON/STAND-BY button to turn the power on.

3Press the AUDIO IN button on the remote control or FUNCTION button repeatedly on main unit to select AUDIO IN function.

4Play the connected equipment. If volume level of the connected device is too high, sound distortion may occur. Should this happen, lower the volume of the connected device. If volume level is too low, increase the volume of the connected device.

Note:

To prevent noise interference, place the unit away from the television.

■■ Headphones

●● Do not turn the volume on to full at switch on and listen to music at moderate levels. Excessive sound pressure from earphones and headphones can cause hearing loss.

●● Be sure your headphone has a 3.5 mm (1/8”) diameter plug and impedance between 16 and 50 ohms. The recommended impedance is 32 ohms.

●● Before plugging in or unplugging the headphone, reduce the volume.

●● Plugging in the headphone disconnects the speakers automatically. Adjust the volume using the VOLUME (+ or -) on the main unit or VOL +/- on the remote control.

Troubleshooting chart

Many potential problems can be resolved by the owner without calling a service technician.

If something is wrong with this product, check the following before calling your authorised SHARP dealer or service centre.

1-99 minutes

Desired time

■■ General

Sleep operation will	Timer playback start	Symptom	Possible cause
automatically stop	time	●●The clock is not set to	●●Did a power failure occur?
Enhancing your system		the correct time.	●●Reset the clock. (Refer
			page 7)
The connection lead is not	included. Purchase a	●●When a button is	●●Set the unit to the power
		pressed, the unit does	stand-by mode and then
commercially available lead as shown below.
		not respond.	turn it back on.
			●●If the unit still
			malfunctions, reset it.
			(Refer page 23)
		●●No sound is heard.	●●Is the volume level set to
			“Min”?
			●●Are the headphones
			connected?
			●●Is the unit too far from the
			Bluetooth stereo audio
Portable			source device?
audio			●●Is the unit paired with the
player, etc.			Bluetooth stereo audio
			source device?
Audio cable		●●Bluetooth sound	●●Is the unit too near to a
(not supplied)		is interrupted or	device that generates
		distorted.	electromagnetic
■■ Listening to the playback sounds of			radiation?
			●●Is there any obstacle
portable audio player, etc.			between the unit and the
1 Use a connection lead to connect the portable audio			Bluetooth stereo audio
			source device?
player etc. to the AUDIO IN socket. When using video

equipment, connect the audio output to this unit and

the video output to a television.

E-22