JBL EVO1.324 manual Important Safety Information Read this Carefully

Page 3

IMPORTANT SAFETY INFORMATION - READ THIS CAREFULLY

This equipment has been tested and found to comply with the following European and international standards for Electromag- netic Compatibility and Electrical Safety:

Radiated Emmissions (EU): EN55022B (1992)

RF Immunity (EU): IEC801-3 (1994)

Electrostatic Discharge(EU): IEC801-2 (1984)

Fast Transients(EU): IEC801-4 (1988)

Electrical Safety (EU): EN60065 (1994)

Electrical Safety(USA): UL6500/ETL (1996)

Electrical Safety(CAN): CAN/CSA-E65/ETLc (1996)

Before using the apparatus read these instructions, follow all instructions, heed them and keep in a safe place.

Clean only with a damp cloth. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not defeat the safety purpose of the grounding type plug. A grounding plug has two blades and a third grounding prong. The third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replace- ment of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience recepticals and the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.

Unplug this apparatus during lightning storms or when not in use for a long time.

WARNING – TO REDUCE THE RISK OF FIRE OR SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

DO NOT REMOVE COVERS, NO USER SERVICABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS EQUIPMENT MUST BE GROUNDED.

!

CAUTION

ATTENTION

 

 

RISK OF ELECTRONIC SHOCK

RISQUE DE CHOC ELECTRIQUE

 

DO NOT OPEN

NE PAS ENLEVER

 

DO NOT EXPOSE

NE PAS EXPOSER A

 

TO RAIN OR MOISTURE

LA PLUIE NI L'HUMIDITE

IT SHOULD NOT BE NECESSARY TO REMOVE ANY PROTECTIVE GROUND OR SIGNAL CABLE SHIELD CONNECTIONS TO PREVENT GROUND LOOPS. ANY SUCH DISCONNECTIONS ARE OUTSIDE THE RECOMMENDED PRACTICE OF JBL PROFESSIONAL AND WILL RENDER ANY EMC OR SAFETY CERTIFICATION VOID.

For continued compliance with international EMC legislation ensure that all input and output cables are wired with the cable screen connected to Pin 1 of the XLR connectors. The input XLR Pin 1 is connected to the chassis via a low value capacitor, providing high immunity from ground loops while ensuring good EMC performance.

Image 3
Contents EVOi.324 N T E N T S EVOi.324Important Safety Information Read this Carefully Welcome T R O D U C T I O NS I G N O V E R V I E W A T U R E S XLR Audio / Communication Input Switch-Mode Power SupplyCompact Design Handle/GripOutput on Generic Mixer EVOi.net Rear Power RequirementsPower Cycle Boot-up Times EVOi.324 RearRectangular-Shaped Room Fan-Shaped Room P L I C a T I O N SSchools and Sports Facilities Performance Venues Places of WorshipHorizontal Coverage = Vertical Coverage = EVO Sound System Design BasicsEVOi.324 Coverage Angles Horizontal Coverage Angles Vertical Coverage AnglesArea Coverage Throw RatioStereo and Arrays Using More Than One SpeakerAiming EVO Maximum Performance GuidelineBasic Delay Speaker Placement When to use Delay SpeakersSmall Rectangular Room Main Mono Longer Rectangular Room Main Mono + 1 Delay MonoSmall/Wider Rectangular Room Main Stereo Longer/Wider Rectangular Room 2 Main Stereo + 2 Delay StereoUse EVOi.net To set actual delay and level Delay Medium Fan Shaped Room 2 Main Mono Array Small Fan Shaped Room Main MonoLarge Fan Shaped Room Main Mono Array + 2 Delay Mono Instructions for Painting I N T I N GEyebolt Kit InstallationOverview SuspensionInstalling Feet Foot KitPlaceholder Bolt Power LED is Flashing TroubleshootingAC Power EVOi.324 doesn’t power upAC Power Requirements EVOi.324 Sensitivity ChartP E N D I C H N I C a L D a T a O i 2 4 Specification sR R a N T Y JBL Limited WarrantyT E S D E Harman International Company