Specifications
Model P207
1750 RPM+ | U. .S. | Metric |
Flow (Continuous) @ 2000 PSI (140 Bar) | 0.9 GPM | 3.4 L/min |
Flow (Intermittent) @ 2500 PSI (175 Bar) | 0.9 GPM | 3.4 L/min |
3450 RPM+ |
|
|
Flow (Continuous) @ 2000 PSI (140 Bar) | 1.7 GPM | 6.4 L/min |
Flow (Intermittent) @ 2000 PSI (140 Bar) | 1.7 GPM | 6.4 L/min |
Maximum Inlet Pressure | 145 PSI | 10 Bar |
Plunger Diameter | 0.47” | 12 mm |
Stroke | 0.25” | 6.3 mm |
Max. Temperature of Pumped Fluids | 160o F | 70o C |
Inlet Ports | (2) 1/2" BSP | |
Discharge Ports | (2) 3/8" BSP | |
Shaft Rotation | Top of Pulley Towards Fluid End | |
Crankshaft Diameter | 0.98” | 24 mm |
Key Width | 0.31” | 8 mm |
Shaft Mounting | Right Side Facing Manifold | |
Weight | 11.7 lbs | 5.3 Kg |
Crankcase Oil Capacity | 7.5 fl.oz | 0.22 Liters |
Extended Crankcase Oil Capacity | 9.0 fl.oz | 0.27 Liters |
Volumetric Efficiency @ 1750 RPM | 0.94 | |
Volumetric Efficiency @ 3450 RPM | 0.87 | |
Mechanical Efficiency @ 3450 RPM | 0.86 | |
+Positive inlet pressure required
Consult the factory for special requirements that must be met if the pump is to operate beyond one or more of the limits specified above.
NOTE:
|
| In order to drive the pump from the side opposite the present shaft | ||||||
|
| extension, simply remove the valve casing from the crankcase and | ||||||
|
| rotate the pumps 180 degrees to the desired position. Be certain to | ||||||
|
| rotate the seal case (item #20) as well, so that the weep holes are | ||||||
|
| down at the six o'clock position. Exchange the oil fill and the oil | ||||||
|
| drain plugs, also. Refer to the repair instructions as necessary for | ||||||
|
| the proper assembly sequence. |
| HORSEPOWER RATINGS: | ||||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| The rating shown are the power |
|
|
|
|
|
|
|
| requirements for the pump. Gas |
| P207 HORSEPOWER REQUIREMENTS | |||||||
| engine power outputs must be | |||||||
| RPM | GPM | 1000 PSI |
| 1500 PSI | 2000 PSI | 2500 PSI* | |
|
| approximately twice the pump | ||||||
| 500 | 0.26 | 0.2 |
| 0.3 | 0.4 | 0.4 | |
|
| power requirements shown above. | ||||||
| 1000 | 0.51 | 0.4 |
| 0.5 | 0.7 | 0.9 | |
|
|
| ||||||
| 1750 | 0.90 | 0.6 |
| 0.9 | 1.2 | 1.6 | We recommend a 1.15 service factor |
| 3000 | 1.48 | 1.0 |
| 1.5 | 2.0 | 2.6 | |
| 3200 | 1.58 | 1.1 |
| 1.6 | 2.2 | 2.7 | be specified when selecting an |
| 3450 | 1.70 | 1.2 |
| 1.8 | 2.3 | 2.9 | electric motor as the power source. |
*Intermittent duty only |
|
|
| To compute specific pump horse | ||||
|
|
| power requirements, use the | |||||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| following formula: |
5