Heat Controller MSS-018B/A, MSH-0186/A, MSH-01 2B/A manual Connect the cable to the indoor unit

Page 36

2) Connect the cable to the indoor unit

1.Connect the wires to the terminals on the control board Individually according to the outdoor unit connection.

"Ensure that the color of the wires of outdoor unit and the terminal No. are the same as those of indoor unit respectively.

"Be sure to refer to the wiring diagram label inside the cover control and carry out the correct field wiring.

Wrong wiring can cause the unit to misoperate to result in a fire hazard.

"Check local electrical codes and any specified wiring instructions or firnhatlons.

2.Attach the Grille onto the cabinet.

"Grasp lower the left and right side of the Grille and engage four tabs on the top inside edge of the chassis.

"Press the Grille toward the chassis until it will be back into place.

-36-

Image 36

Contents Heat CONTROLLER, INC Contents Functions Indoor UnitAuto Wind Remote Controller Operation Owoff Operation Mode SelectionFan Speed Selection Product SpecificationsCooling Only Power Supply 17Z,-WAir Circulation Oumw 1 ,260Product SpecificationsCooling & Heating Jzý, Installation plate Indoor UnitTubing hole cover 9k, 12k 18k, 24kOutdoor Unit Gas sideModel DIM Refrigeration Cycle Diagram Cooling Only ModelsCooling & Heating Models Camay a HeatingHeat Evaporator I / \Indoor Wiring Diagram Indoor Wiring DiagramMSS-012, MSS-018, MS18, MSS-024, MSF4424 IroomOutdoor Unit Cooling Only Models 9k, 12k18k 24k LO.a12k 18k 24k Time delay Safety Control Cooling Operation ModeFunction of main control Airflow Direction ControlAuto Operation Electronic control mode Intake AIR Temp Setting TEMP. +1FSetting TEMP. -10F Modeo MODE1rStartMODE2 MODE3 MODE4 Modes EndSoft Dry Operation Mode Intake AIR TESelecting Low OFF CompressorIntake AIR Temp Setting TEMP. +60F Setting TempHeating Operation Modeonly Heating Model IndoorRý u Pipe TempDefrost OFF Defrost onCooling or Heating Mode with Sleep Mode Auto Control Setting TEMP. -1FSetting Temp Forced OperationCrank Case Heater Coil Controlonly Heating model ICJIndoor OutdoorDisplay Function Self-diagnosis FunctionBuzzer Sound DiagnosisInstallation Is toxic when burnedWhen connecting refrigerant tubing When servicingRoof Top Installations Selection of the best locationPiping length and the elevation Indoor Unit Installation Avoid areas where electrical wiring, conduits orWire or gas line can cause death or injury Lower left and right side of Installation PlatePiping and Drainage of Indoor Unit Preparation of PipingsStarted Poo 113 H IW-0Connection of Pipings For right rear pipingLlj 5kgm39.8ft.ibsFor the left pipings Insert the connecting cable into the indoor unit Tape the tubing, drain hose and the connectingIndoor unit installation Installation plate. Engage the two hooks of the rearDrain hose Taping Connecting Pipings and the cable to Outdoor unit Connecting the pipings to the Outdoor unit Connection of the cable Terminals and fasten the wire tightly with the fixing screw 2sanoevChecking the Drainage Connect the cable to the indoor unit Attach the Grille onto the cabinetBwid Forming the pipingsPage Page Temperature, Pressure, Ampere Chan Settfemont of Outdoor UnitEvaluation of theperformance Name and Function-Remote Controller MG OFF Timer ButtonSleep Mode Auto Button Operation displayQs Operation Mode Selection Button Start/Stop ButtonBe careful not to lose the clip when reassem- bling Cooling & HeatingRemove the securing screws To remove the Control BoxRemove 2 securing screws Page To remove the Grille from the Chassis To remove the Control BoxTo remove the Discharge Grille To remove the EvaporatorRemove three screws fixing control box and motor Unhook the tab on the left inside edgeTo remove the Cross-Flow Fan To remove the Fan MotorCycle Troubleshooting Guide Trouble analysisCause of Trouble Turn off Main Power Cý After 10 seconds Connector related to CN-POWER Connector related to CN-FANDisplay PWB Assy Check Connector related to CN-DC/DC Does beeping sound is made from the Indoor Unit?Product Is not operate with the remote controller R751K C711000PF Micom PIN Check Receiver AssyTurn on Main Power Compressor/Outdoor Fan are unable to driveWhen Indoor Fan does not operate When Vertical Louver does not operate When a comunication error occurs Operation indicator of Indoor unit blinks five timesPhenomena in case of connecting error Indoor UnitCN-UP/DOWN CN-THCN-POWER RY-COMP +0 , ýOutdoor Unit CN-TRANS CN-FANVoltage of Connectors according to Indoor Fan Speed Electronic Control Device Optional FunctionMain PWB ASSYOutdoor Unit Optional Function Model1OK 18k, 24k LDt ftnASM LD2 LD4Schematic Diagram Page BA ýJ Plate Installation Remote ControllerHeat OTY Remark Parts Name ControllerIndoor Unit18k, 24k Parts Name Motor Assy Chassis Assy7DDD \ , \ Tom, .ý M m mm9k, 12k Base Weld ASM Condenser Compressor ASMReversing Valve Reversing Coil Front Panel AssyBarrier TOP Cover ASM Rear Panel31 CAP Capillary Final ASM HEATERCRANK-CASE1 Heat QTY RemarkOutdoor Unit18k `Ty L8k MSS-018A MSH-018A171 Reversing Coil QTY Remark PWB ASSY, Main SH-CAPACITORClamp Capacitor Controller Assy Check Valve CAPILLARY, Bent CAPILLARY, Bent Panel Cover Control 29 CAPPANEL, Rear 2021-0024Remark R means service parts ICJ No9O2k MSS-009B MSS-012B 2021-0001Plate Installation Holder Tube Motor Assy Chassis Assy MSS-0188 MSH-018B2021-0001 2021-0074 2010-0003 2021-0069 2021-0005 FAN Assy CrossService VALVE1/4 Service VALVE112 GQ 21kTOP Cover ASM CapillaryFinal ASM HEATERCRANK-CASEHigh Pressure S/W Reversing ValveFAN Motor 2021-0024 I`JMSS-018A MSH-018A Support Valve High Pressure S/W Reversing Coil SAT City RemarkPWBASSY,MAIN UTY Remark 2035-0004 2035-00062021-0021 2050-0001 Extra FAN Barrier ASMHeat CONTROLLER, INC