Heat Controller BDE-123, BD-101, BD-123, BDE-103, BD-81 manual

Page 13

NOTES

—Replacement of the refrigeration cycle.

1.When replacing the refrigeration cycle, be sure to discharge the refrigerant system using a FreonTM recovery System.

If there is no valve to attach the recovery system, install one (such as a WATCO A-1) before venting the FreonTM. Leave the valve in place after servicing the system.

2.After discharging the unit completely, remove the desired component, and unbrace the pinch-off tubes.

3.Solder service valves into the pinch-off tube ports, leaving the valves open.

4.Solder the pinch-off tubes with Service valves.

5.Evacuate as follows.

1)Connect the vacuum pump, as illustrated Fig. 18A.

2)Start the vacuum pump, slowly open manifold valves A and B with two full turns counterclockwise and leave the valves closed. The vacuum pump is now pulling through valves A and B up to valve C by means of the manifold and entire system.

CAUTION

If high vacuum equipment is used, just crack valves A and B for a few minutes, then open slowly with the two full turns counterclockwise. This will keep oil from foaming and being drawn into the vacuum pump.

3)Operate the vacuum pump for 20 to 30 minutes, until 600 microns of vacuum is obtained. Close valves A and B, and observe vacuum gauge for a few minutes. A rise in pressure would indicate a possible leak or moisture remaining in the system. With valves A and B closed, stop the vacuum pump.

4)Remove the hose from the vacuum pump and place it on the charging cylinder. See Fig. 18B. Open valve C.

Discharge the line at the manifold connection.

5)The system is now ready for final charging.

6.Recharge as follows :

1)Refrigeration cycle systems are charged from the High-side. If the total charge cannot be put in the High-side, the balance will be put in the suction line through the access valve which you installed as the system was opened.

2)Connect the charging cylinder as shown in Fig. 18B. With valve C open, discharge the hose at the manifold connection.

3)Open valve A and allow the proper charge to enter the system. Valve B is still closed.

4)If more charge is required, the high-side will not take it. Close valve A.

5)With the unit running, open valve B and add the balance of the charge.

a.Do not add the liquid refrigerant to the Low- side.

b.Watch the Low-side gauge; allow pressure to rise to 30 lbs.

c.Turn off valve B and allow pressure to drop.

d.Repeat steps B and C until the balance of the charge is in the system.

6)When satisfied the unit is operating correctly, use the pinch-off tool with the unit still running and clamp on to the pinch-off tube. Using a tube cutter, cut the pinch-off tube about 2 inches from the pinch-off tool. Use sil-fos solder and solder pinch-off tube closed. Turn off the unit, allow it to set for a while, and then test the leakage of the pinch-off connection.

— 13—

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Heat CONTROLLER, INC Preface ContentsFor BD-81/BD-101 SpecificationsModels RemarkBD-123 For BD-123Items Models For BDE-103/BDE-123BDE-103 BDE-123 Control Locations FeaturesCooling only Model Operation VentilationCooling and Heating Model Operation Mechanical Parts Disassembly InstructionsFront Grille CabinetORIFICE, Heater Assy and Turbo FAN AIR Handling Parts2 FAN Shroud Electrical PartsMotor CompressorRotary Switch Power CordThermostat Condenser Refrigeration CycleEvaporator Capillary TubePage Pulling Vacuum Installation Requirements InstallationInstallation Hardware Electrical ServiceItems in Installation Hardware HOW to InstallProcedure a Top View Procedure BTrim 2 ea Wall Procedure CHigh Electrical Requirements Electrical SafetyElectrical Data for 115V Model USE of Extension CordsOutside Dimensions Troubleshooting GuidePiping System Troubleshooting Guide Fails to Start Complaint Cause Remedy Name Plate Rating Minimum Maximum Room AIR Conditioner Voltage LimitsComplaint Cause Remedy Circuit Diagram Schematic DiagramModel BD-81/BD-101/BD-123 Description QTYModel BDE-103/BDE-123 Model BD-81/BD-101/BD-123/BDE-103/BDE-123 Exploded ViewModel BD-81/BD-101 Replacement Parts ListDescription Remark BD-81 BD-101BD-123 Model BD-123Model BDE-103/BDE-123 Heat CONTROLLER, INC

BD-81, BDE-123, BDE-103, BD-123, BD-101 specifications

The Heat Controller series, including the BD-123, BDE-123, BD-101, BDE-103, and BD-81 models, offers an impressive range of features and innovative technologies designed to provide efficient heating and cooling solutions for a variety of environments. Each model is engineered to stand out in performance, making them suitable for both residential and commercial applications.

The BD-123 model boasts an advanced Energy Efficiency Ratio (EER) that ensures users enjoy reduced energy consumption without compromising comfort. This unit is equipped with an intelligent temperature control system that adapts to the surrounding environment, optimizing heating or cooling as needed. Additionally, its sleek, modern design contributes to both aesthetics and functionality, making it an integral part of any space.

The BDE-123 enhances the functionality of the BD-123 by incorporating smart connectivity options. Users can control the temperature of their space remotely via smartphone applications, allowing for greater convenience and energy management. Furthermore, this model features a filter reminder system that alerts users when it’s time for maintenance, prolonging the unit's lifespan and ensuring peak performance.

The BD-101 model is designed with an emphasis on compactness and versatility. Its lightweight structure allows for easy installation in small spaces, making it ideal for apartments and small offices. With multi-speed fan settings, this model provides customizable airflow, catering to individual preferences and requirements.

The BDE-103 enters the market as a top-tier option, featuring advanced inverter technology. This innovative approach significantly reduces power consumption while maintaining consistent temperature control. The BDE-103 also prides itself on quiet operation, allowing users to enjoy a peaceful atmosphere without the disruptive noise often associated with traditional systems.

Lastly, the BD-81 is tailored for users seeking affordable yet reliable heating and cooling solutions. Despite its lower price point, it does not compromise on quality, offering essential features such as adjustable thermostats and programmable timers. This model makes it accessible for budget-conscious users while still providing comfort and efficiency.

In summary, the Heat Controller BD-123, BDE-123, BD-101, BDE-103, and BD-81 models cater to a variety of needs. With a combination of energy efficiency, smart technology, compact design, and affordability, these models are designed to ensure optimum comfort in any setting while prioritizing user convenience and sustainability. Whether for a small apartment or a large commercial space, there is a Heat Controller model that meets the demands of modern living.
Top Page Image Contents