Philips AZT9500 warranty Features

FEATURES FEATURES

Selecting a track and searching

Selecting a track during playback

• Briefly press ∞ or § once or several times to skip to the current, previous or next track.

yPlayback continues with the selected track, and the track’s number is displayed.

Selecting a track when playback is stopped

1Briefly press ∞ or § once or several times to select the desired track. The track number is displayed.

2Press 2; to start CD play.

yPlayback starts with the selected track.

Searching for a passage during playback

1Keep ∞ or § pressed to find a particular passage in a backward or forward direction.

ySearching starts while playback continues at low volume. After 2 seconds the search speeds up.

2Release the button when you reach the desired passage. yPlayback continues from this position.

Notes: – If the player is in SCAN mode (see MODE chapter), searching is not possible.

–In shuffle, shuffle repeat all or repeat mode (see MODE

chapter), or while playing a program, searching is only possible within the particular track.

This set complies with the radio interference requirements of the

European Community.

Programming track numbers

You can store up to 30 tracks to play in a program. A single track may be stored more than once in the program.

1 While playback is stopped, select a track with ∞ or §.

2Press PROGRAM to store the track.

yprogram lights up; the track number

programmed and P with the total number of stored tracks are displayed.

3 Select and store all desired tracks in this way. program

4Press 2; to start playback of your selected tracks. yprogram is shown and playback starts.

•You can review the program by pressing PROGRAM for more than 2 seconds. yThe display shows all the stored tracks in sequence.

Notes: – If you press PROGRAM and there is no track

selected, is displayed.

– If you try to store more than 30 tracks, FULL is displayed.

Clearing the program

• While playback is stopped, press 9 to clear program. yCLEAr is displayed once, program goes

off, and the program is cleared.

program

Note:The program will also be cleared if the power

supply is interrupted, or if the CD-player lid is opened, or if the set switches off automatically.

Selecting different playing possibilities− MODE

It is possible to play tracks in random order, to repeat a single track or the entire CD, and to play the first few seconds of each track.

1 Press MODE during playback as often as required in

order to activate one of the following ‘modes’. The active mode is shown in the display.

yshuffle : All tracks of the CD are played in random order until all of them have been played once.

yshuffle repeat all : All tracks of the CD are played repeatedly in random order.

yrepeat : The current track is played repeatedly. repeat all shuffle

yrepeat all : The entire CD is played repeatedly.

ySCAN: The first 10 seconds of each of the remaining tracks are played in sequence.

2Playback starts in the chosen mode after 2 seconds.

•To return to normal playback, press MODE repeatedly until the display shows no active modes.

ESP / Power Save Mode

With a conventional portable CD-player you might have experienced that the music stopped e.g. when you were jogging. The ELECTRONIC SKIP PROTECTION prevents loss of sound caused by light vibrations and shocks. Continuous playback is ensured. However ESP does not prevent playback interruptions during vigorous running. It also does not protect the unit against any damage caused by dropping! In this set ESP is default ON. It is possible to set ESP off. and enter the Power Save Mode.(PS). PS helps to extend battery lifetime for longer playback.

•Press ESP once. y disappears.

• Press ESP again . yPS is displayed once

ESP on ➟ ESP off ➟ Power Save ➟ESP on

RESUME and HOLD

You can interrupt playback and continue (even after an extended period of time) from the position where playback stopped (RESUME) and you can lock all buttons

of the set so that no action will be executed (HOLD). Use	OFF • RE
	SUME • HOLD

the RESUME–HOLD–OFF slider for these functions.

RESUME – continuing from where you have stopped

1Switch the slider to RESUME during playback to acti- vate RESUME.

yresume is shown.

2 Press 9 whenever you want to stop playback. resume

3Press 2; whenever you want to resume playback.

yresume is shown and playback continues from where you have stopped.

•To deactivate RESUME, switch the slider to OFF. yresume goes off.

HOLD – locking all buttons

You can lock the buttons of the set by switching the slider to HOLD. Now, when a key is pressed, no action will be executed. This is of use, for example, when transporting the player in a bag. With HOLD activated,

you can avoid accidental activation of other functions.

1Switch the slider to HOLD to activate HOLD.

yAll buttons are locked. HoLd is shown when	hold
you press any button.	resume

2To deactivate HOLD, switch the slider to OFF.

Note: If you deactivate HOLD by switching the slider to RESUME, you will be activating the RESUME function.