Philips AZT9500 warranty Troubleshooting

FEATURES TROUBLESHOOTING

Radio Play

You can tune to any FM or MW station automatically or manually. Stereo stations are indicated by ST.

1 Press FM/ MW to switch the radio on.

2 Press FM/ MW repeatedly if necessary to select the desired waveband.

yFM or MW is shown.

Tuning to radio stations automatically
1 Keep ∞ or § pressed for at least 1 second.	FM
yThe radio tunes to a station with sufficient
strength and radio play starts. The current
waveband and frequency are displayed.

2Repeat searching until you find the desired radio station.

Tuning to radio stations manually

1 Keep ∞ or § pressed.

2 Release ∞ or §, then briefly press ∞ or § again when you are close to the desired frequency.

3 Briefly press ∞ or § repeatedly until you reach the

Troubleshooting

WARNING: Under no circumstances should you try to repair the set yourself as this will invalidate the warranty. If a fault occurs, first check the points listed, before taking the unit for repair. If you are unable to solve a problem by following these hints, consult your dealer or service center.

The CD player has no power, or playback does not start

•Check that your batteries are not dead or empty, that they are inserted correctly, that the contact pins are clean.

•Your adapter connection may be loose. Connect it securely.

•For in-car use, check that the car ignition is on. Also check player’s batteries.

The indication no diSC is displayed

•Check that the CD is clean and correctly inserted (label-side upward).

•If your lens has steamed up, wait a few minutes for this to clear.

The indication nF diSC is displayed

• CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.

The indication HOLD is on and/or there is no reaction to controls

•If HOLD is activated, then deactivate it.

•Electrostatic discharge. Disconnect power or remove batteries for a few seconds.

The CD skips tracks

desired frequency.

FM

• The CD is damaged or dirty. Replace or clean the CD.

yRadio play starts. The current waveband and frequency are displayed.

•To switch from radio play to CD play, press 2;.

•Press 9 to switch the radio off.

Note: In case of interferences in stereo mode, press. MODE to switch to mono.

• RESUME, SHUFFLE or PROGRAM is active. Switch off whichever is on.

Antennas

• FM: The headphone wire is used as an FM antenna. If necessary, move it for optimum reception.

• MW: The internal MW antenna is directed by turning the player.

Storing radio stations

You can store up to 30 radio stations. Select a preset number 1-24 FM stations and a number 1-6 for MW station.

1 Tune to a desired radio station and press PROGRAM.

2Press 3 or 4 repeatedly if necessary to select the number that should be assigned to this radio station.

3Press PROGRAM while PRESET is blinking to confirm the storage.

yPRESET, the waveband, the frequency and the	PRESET FM ST
preset number of the stored station are dis-
played.

4Store all desired stations this way.

Note: Already stored stations can be recognized by the indicator PRESET and the preset number.

Tuning to a stored radio station

1Select the waveband.

2Press 3 or 4 repeatedly if necessary to select the preset number of the desired radio station.

yRadio play starts. PRESET, the waveband, the frequency and the preset number of the stored station are displayed.

Troubleshooting

No sound or bad sound quality.

•PAUSE might be active. Press 2;.

•Loose, wrong or dirty connections. Check and clean connections.

•Volume might not be appropriately adjusted. Adjust the volume.

•Strong magnetic fields. Check player’s position and connections. Also keep away from active mobile phones.

•For in-car use, check that the cassette adapter is inserted correctly, that the car cassette player’s playback direction is correct (press autoreverse to change), and that the cigarette lighter jack is clean. Allow time for temperature change.

CAUTION

Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.