Philips 1 manual Set Up, Positioning the projector and screen, Mains supply, To Raise

Page 8

6. Set Up

Positioning the projector and screen

• Place the projector on a stable, level surface, out of direct

sunlight and away from sources of excessive dust, dirt, heat,

water, moisture, vibration and strong magnetic fields.

Face the projector towards the screen for the best picture

results. To determine the distance for the desired size,

please refer to the Projection Assistant, a calculation

programme included on the CD-ROM.

• The screen should be positioned so that it is not directly

touched by sunlight or artificial light, as this will wash out the

colours of the picture, making it hard to see.

• The projector can be used for both front projection, rear

projection and ceiling projection applications. As default

factory setting, the projector has been set up for front

projection. You can change to rear or ceiling projection via the

OSD menu. See ‘Rear screen projection’ and ‘Ceiling-mount

projection’ under ‘Operation - Display and picture control’ for

The Standby Warning screen will appear for 20 seconds.

Warning

If the projector is switched off you have to wait 1 minute before you can switch on the projector again.

To switch off projector keep stand-by key pressed for 3 seconds.

Press OK key to remove this warning.

 

further instructions.

Choose a screen size suitable for the number of viewers and

 

the size of the room.

Picture quality is best when you sit directly in front of the

 

projector screen.

Mains supply

1.Insert the mains lead into the projectors Power socket and connect it to the wall socket.

Note: The standby indicator lights up red, the projector is now in the Power/Standby mode.

Note: The Stand by Warning screen can be removed by keeping the Stand by On button pressed for 3 seconds.

If the Stand by On button is pressed for 3 seconds the first time (step 3), the projector is switched back into the power standby mode without the Standby Warning screen being displayed.

5.To switch off the mains supply completely, pull the mains plug out of the wall socket.

Note: Before disconnecting the mains lead, make sure that the

cooling fan has stopped (about 3 minutes after the projector has been switched to Power Standby).

Adjusting the focus and size of the image

Use the Zoom ring to adjust the size of the image.

Use the Focus ring to adjust the focus of the image.

Zoom ring

Focus ring

2.Remove the lens cap.

3.Press the Stand by

On button to switch on the projector.

The lamp indicator flashes green.

When the projection lamp is on, the lamp indicator lights up green while the lamp is starting up and the start- up screen appears for several seconds.

4.Press the Stand by On button again to switch the projector back into the power standby mode.

PHILIPS

Multimedia Projectors

Adjusting the vertical and horizontal angle of the projector

Vertical angle

Use the Height/Level Adjusters to adjust the vertical angle of the projector as specified under ‘Positioning the projector and screen’.

A

A

B

B

To Raise:

Keep both adjusters (A) pressed and lift to raise the projector.

– The projector feet (B) will come out.

8

Image 8
Contents Page SVGA/XGA version XGA Impact Available as accessory for SVGA/XGA versionControls and connections Introduction Things You Should Know FCC WarningImportant Safeguards Projector Features On projector fig On compact remote control SVGA/XGA version figFunctional Overview See illustrations On trackball remote control XGA Impact version fig Data source connections figVideo source connections Other connectionsSet Up Adjusting the focus and size of the imagePositioning the projector and screen Mains supplyInserting the batteries in the trackball remote control To LowerHorizontal angle horizon Moving the projectorInstallation Video/computer cables and adapter Video/computer cables and adapterAdapter Installation Connecting to a computerOptional Philips Optional Installation Connecting to video equipmentConnecting to video equipment Amplifier Installation Connecting to audio equipmentConnecting to audio equipment Monitor cable Optional Installation Connecting to an external monitorConnecting to an external monitor Operation Preparation For exampleOperation Preparation/Display and picture control Tip for Windows usersOperation Display and picture control Activate PanOperation Display and picture control/Audio control Rear screen projectionCeiling-mount projection Audio ControlOperation Other settings Maintenance Lamp Replacement LampResetting the lamplife time Use cursor control to select Lamp counter in the sub menuTroubleshooting