Haier HDU-42HT03/H Installation of air suction and discharging duct, Drainage Test, Procedures

Page 28

Installation Manual For Indoor Unit

(d)When constructing drain piping for several units, position the common pipe about 100 mm below the drain outlet of each unit as shown in the sketch. Use VP-30(11/4") or thicker pipe for this purpose.

Secure the elevation as high as possible (approx. 100 mm)

(e) The stiff PVC pipe put indoor side should be heat insulated.

A downhill grade of

VP 30

 

1/100 or more

 

(f)Avoid putting the outlet of drain hose in the places with irritant gas generated. Do not insert the drain hose directly into drainage, where the gas with sulfur may be generated.

(g)Backwater bend

Because the drain spout is at the position, which negative pressure may occur. So with the rise of water level in the drain pan, water leakage may occur. In order to prevent water leakage, we designed a backwater bend.

The structure of backwater bend should be able to be cleaned. As the below figure shown, use T type joint. The backwater bend is set near the air conditioner.

As figure shown, set a backwater bend in the middle of drain hose.

H1

H2

Drainage Test

H1=100mm or the static pressure of air sending motor H2=1/2H1 (or between 50~100mm)

1Conduct a drainage test after completion of the electrical work.

2During the trial, make sure that drain flows properly through the piping and that no water leaks from connections.

3In case of a new building, conduct the test before it is furnished with the ceiling.

4 Be sure to conduct this test even when the unit is installed in the heating season.

Procedures

1Supply about 1000 cc of water to the unit through the air outlet using a feed water pump.

2Check the drain while cooling operation.

6.Installation of air suction and discharging duct

muffler cavity (air sending)

Enlarging chart of

 

 

 

Sacking joint

profile chart A

Insulation

A

Vibration resistance hook

Air volume adjuster

Air outlet

Air conditioner

Ceiling

main unit

Air suction grille with air filter

 

Checking meatus

Please consult the after-sales service worker of Haier Air Conditioner for the choosing and installation of suction inlet, suction duct, discharging outlet and discharging duct. Calculating the design drawing and outer static pressure, and choose the discharging duct with proper length and shape.

27

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Duct Type AIR Conditioner Table of Contents Disposal of the old air conditioner Safety Precautions Make sure the system is groundedDo not operate the system while Machine is adaptive in following situation Parts and Functions Parts and Functions Operation Used to select your desired tempSleep Auto DRY Fan operation Auto RUN, COOL,HEAT and DRY operation Timer operation Timer ON-OFF Cooling, dehumidifying mode Heating mode This series changeover switch is set 1. on 2.OFF 3.OFF 4.OFF Malfunction Unit fails to startCooling or heating is not sufficient Cooling is not sufficientMalfunction Case of Auto mode, operation mode is changed automati Followings are not malfunctionWater flowing sound is heard This is caused by heat expansion or contraction of plasticsCare and Maintenance Points to observeFor Preparation of HeatingHot Keep HOT KEEPis operated in the following casesIs The Unit Installed Correctly Installation placeWhen you change your address or the installation place For inspection and maintenanceInstallation Manual For Wire Controller Install wire controllerWire size Shielded wire GroundHint HintInstallation Manual For Indoor Unit Serious injury are listedChoose installation place Height of ceilingPreparation before installation Hanger bolts installationInstallation of indoor unit Adjusting to the levelnessDrain Piping Good pipingInstallation of air suction and discharging duct ProceduresDrainage Test Stiff PVC pipe put indoor side should be heat insulatedChosen chart of simple duct Each bend takes as a3~4m long straight ductSquare duct Hm 3/n MmxmmExamples of improper installation Rotate this switch Operation method of fan controllerRefrigerant pipe Installation Manual For Electric Wiring Wiring connectionBreaker Current HDU-42CF03/HHaier Group

HDU-42HT03/H specifications

The Haier HDU-42HT03/H is a cutting-edge heating, ventilation, and air conditioning (HVAC) solution designed to provide comfort and efficiency for residential and commercial spaces. This model stands out due to its innovative features, advanced technologies, and reliable performance.

One of the key features of the Haier HDU-42HT03/H is its impressive cooling and heating capacity. With a nominal cooling capacity of 4.2 kW and a heating capacity of 5.0 kW, this model is suitable for medium-sized rooms, ensuring that spaces remain comfortable regardless of outdoor temperatures. Its Inverter technology allows for precise control of the compressor speed, resulting in faster cooling and heating, less energy consumption, and quieter operation.

The unit’s energy efficiency is highlighted by its high SEER (Seasonal Energy Efficiency Ratio) and SCOP (Seasonal Coefficient of Performance) ratings, which contribute to lower electricity bills and reduced environmental impact. The HDU-42HT03/H also features a programmable thermostat, allowing users to set specific heating and cooling schedules, optimizing energy use while maintaining comfort.

For enhanced air quality, the Haier HDU-42HT03/H comes equipped with a multi-stage filtration system that effectively captures dust, allergens, and other airborne particles. This ensures that the air circulated within the space is clean and healthy, making it an excellent choice for individuals with allergies or respiratory issues.

Additional technological advancements in the HDU-42HT03/H include the use of eco-friendly refrigerant, which minimizes its impact on the environment. The model also integrates smart technology, allowing for remote operation via a smartphone application. This feature enables users to control the unit from anywhere, providing added convenience and flexibility.

In terms of design, the Haier HDU-42HT03/H is sleek and modern, allowing it to blend seamlessly into various interior styles. Its compact structure makes it suitable for a variety of installation environments, whether in homes or businesses.

Overall, the Haier HDU-42HT03/H is a top-tier HVAC solution, boasting powerful performance, energy efficiency, and user-friendly features. It is an excellent choice for anyone looking to enhance their indoor climate control with a reliable and effective system.
Top Page Image Contents