JVC XL-R5020BK manual Maintenance

Page 43

Maintenance

To get the best performance of the unit, keep your discs and mechanism clean.

General Notes

In general, you will have the best performance by keeping your discs and the mechanism clean.

•Store discs in their cases, and keep them in cabinets or on shelves.

•Keep the disc trays closed when not in use.

To handle discs

When removing a disc from its case, press down the center holder of the case and lift the disc out, holding it by the edges.

• Always hold the disc by the edges. Do not touch its recording surface.

When storing a disc into its case, gently insert the disc around the center holder (with the printed surface facing up).

•Make sure to store discs into the cases after use.

•Be careful not to scratch the surface of

the disc when placing it back in its case.

•Avoid exposure to direct sunlight, temperature extremes, and moisture.

To clean the disc

Wipe the disc with a soft cloth in a straight line from center to edge.

DO NOT use any solvent—such as conventional record cleaner, spray, thinner, or benzine—to clean the disc.

To play new discs

New discs may have some rough spots around the inner and outer edges. If such a disc is used, this unit may reject the disc.

To remove these rough spots, rub the edges with a pencil or ballpoint pen, etc.

Moisture condensation

Moisture may condense on the lenses inside the unit in the following cases:

•After starting the heater.

•When the unit is moved from the extremely hot place to the extremely cold place.

Should this occur, the unit may malfunction. In this case, eject the disc and leave the unit turned on for a few hours until the moisture evaporates.

•DO NOT expose discs to direct sunlight or any heat source or place them in a place subject to high temperature and humidity.

•DO NOT leave discs in a car.

To clean the unit

•Stains on the unit

Should be wiped off with a soft cloth. If the unit is heavily stained, wipe it with a cloth soaked in water-diluted neutral detergent and wrung well, then wipe clean with a dry cloth.

•Since the unit may deteriorate in quality, become damaged or get its paint peeled off, be careful about the followings. —DO NOT wipe it with a hard cloth.

—DO NOT wipe it strong.

—DO NOT wipe it with thinner or benzine. —DO NOT apply any volatile substance such as

insecticides to it.

—DO NOT allow any rubber or plastic to remain in contact with it for a long time.

41

Page 42 Page 44
Image 43
Page 42 Page 44
Contents XL-R5020BK Important for Laser Products For U.S.ATable of Contents Introduction PrecautionsImportant notice Precautions on Disc Playback and RecordingPlayback RecordingSee pages in the parentheses for details Parts IdentificationSTANDBY/ON To operate 3-CD Changer, press Control CD To cancel the reset, press CancelTo operate CD Recorder, press Control CDR Putting the Batteries into the Remote Control Supplied AccessoriesGetting Started To connect an analog component Connecting Other ComponentsAudio component with digital output To connect digital componentsAudio component with digital input Basic Operations Turning On and Off the PowerListening with Headphones To increase the volume level, turn Phone Level control toOn the unit only Playing Back Discs on 3-CD ChangerLoading Discs Playing Back All Loaded Discs-Continuous PlayTo go to another track directly Basic Disc OperationsTo start playing a disc during playback of another disc To go to another trackPrograming the Playing Order of the Tracks-Program Play To modify the program To check the programed contentsCD Changer Multi JOG ¢ Disc trays Play 3 Stop Play ModeRandom indicator also lights up on the display Playing at Random-Random PlayPress Pitch + or − during play Adjusting the Playback Speed-Pitch ControlRepeating Tracks-Repeat Play Prohibiting Disc Ejection-Tray LockPress Eject 0 again Playing Back a Disc on CD RecorderLoading a Disc Playing Back a Disc-Normal Play Press EjectCDR Load a disc onto the CD Recorder disc tray seePress Control CDR, then About MP3 Playing Back MP3 Discs on 3-CD ChangerMP3 Disc Structure Track numbers already played go off from the display Playing Back MP3 DiscsPause Play Stop ButtonsTo go to another group directly Basic MP3 Disc OperationsTo go to another track within a group directly To go to another groupBefore You Start Recording Recording on a CD-R/CD-RWPress one of the disc number buttons CD1, CD2, CD3 you want Recording Manually-Standard RecordingPress ¶ REC/REC Muting Start recordingMenu SET To adjust the analog recording levelPress SET or Menu to finish the adjustment REC Level +/−To fade in and out recording-only for analog source To make a silent portion while recordingTo change the display information while recording Changing the recording speed Preparing for CD Synchronized RecordingFinalizing discs automatically Recording from 3-CD Changer-CD Synchronized Recording CD REC ¶ CancelDisc Direct Recording To release the seamless recording, select Normal Normal initial setting appears on the displayRecording the entire disc without any interruption Multi JOG ¢CD REC One Track RecordingCD REC ¶ Stop 7 forTo program other tracks, repeat step To skip the currently playing track, press CancelTo erase all programed tracks, press Cancel in step Listening Edit RecordingProgram Edit Recording Press Synchro Start playback of the selected external componentMIX Balance Selector Recording from the Two Sources Mixed-Sound Mixing RecordingPause REC Muting ¶ REC/REC Muting Finalizing a disc-CD-R/CD-RW Other Recording FunctionsPress Finalize again to finalize a disc To use Synchronized Recording for recording all tracks Sync ALL initial setting appears on the displayAuto TR on initial setting appears on the display Recording track marks manuallyTurning on or off sampling frequency rate converter Separating recording tracks automaticallyRecording skip marks onto a CD-R/CD-RW-Track Skip Load a recorded disc on the CD Recorder disc tray Erasing tracks only for CD-RW-Track EraseErasing all tracks only for CD-RW-Disc Erase Load an unfinalized disc on the CD Recorder disc trayTo set the clock first time Using the TimerSetting the Clock To adjust the clock againUnit enters off-time setting mode Using Daily Timer and Once TimerHow Timers actually work STANDBY/ON Menu SET CancelTo turn on Playing Timer or Recording Timer Setting Playing TimerSetting Recording Timer Timer PriorityAutomatic source selection Compu Link Remote Control SystemConnection Available functionsMaintenance Glossary Message Signification SolutionSymptom Possible Cause Action TroubleshootingSpecifications Authorized Service Centers Limited Warranty 0502KTYMDWJEM
Top Page Image Contents