Bose AM267565 manual For Cutting

Preparation

•Each speaker enclosure extends into the wall or ceiling, as shown in the gray DO NOT CUT area on the template (Figure 7), and below the grille. The speaker enclosure can be inserted either up or down.

Note: In cold climates where a humidifier is used, avoid inserting the speaker upside-down in an exterior wall to prevent problems with condensation.

Allowing enough room both above and below the hole you draw provides a fallback in case the area below your pilot hole is not suitable for the speaker enclosure.

Figure 7

Template for either rectangular-faced (left) or round-faced (right) speakers

TAPE	WARNING: Make sure the spot chosen is safe for cutting. Do not cut through			TAPE
HERE				HERE
	surfaces that have hazards, such as electrical wiring, conduits or plumbing,
	concealed behind them. If you are not sure, consult a professional installer
	before you proceed.
		8 1/16" (20.5 cm)
		Translations below
	WARNING: Make sure the spot chosen is safe for cutting. Do not cut through surfaces that have hazards, such as electrical
	wiring, conduits or plumbing, concealed behind them. If you are not sure, consult a professional installer before you proceed.
	WARNING: Make sure the spot chosen is safe for		WARNING: Make sure the spot chosen is safe for
	drilling. Do not cut through surfaces that have hazards		drilling. Do not cut through surfaces that have hazards
	concealed behind them, such as electrical wiring,		concealed behind them, such as electrical wiring,
	conduits or plumbing. If you are not sure, consult a		conduits or plumbing. If you are not sure, consult a
	professional installer before you proceed.		professional installer before you proceed.

CUTWHITEOUTAREA	5	1	/		" (14 cm)		Pilot	Hole	WARNING: Make	WHITECUTAREAOUT
				2					is safe for drilling. Do
									not cut through
	WARNING:					Make sure the			surfaces that have
	spot chosen					is safe for			hazards concealed
	drilling. Do not cut through								behind them, such
	professional installer before								before you proceed.
	surfaces that have hazards								as electrical wiring,
	concealed behind them,								conduits or
	such as electrical wiring,								plumbing. If you are
	conduits or plumbing. If you								not sure, consult a
	are not sure, consult a								professional installer
	you proceed.
									WARNING: Make sure the spot
WARNING: Make sure the spot chosen is safe									chosen is safe for drilling. Do not cut
									through surfaces that have hazards
for drilling. Do not cut through surfaces that have									concealed behind them, such as
hazards concealed behind them, such as									electrical wiring, conduits or plumbing.
electrical wiring, conduits or plumbing. If you									If you are not sure, consult a
are not sure, consult a professional installer									professional installer before you
before you proceed.									proceed.
TAPE		DO NOT					English & Translations		DO NOT	TAPE
HERE	CUT AROUND								CUT AROUND	HERE
	GRAY AREA								GRAY AREA

141/2" (36.9 cm)

9" (22.9 cm)

	DO NOT	DO NOT
	CUT AROUND	CUT AROUND
	GRAY AREA	GRAY AREA
	DO NOT	DO NOT
	CUT AROUND	CUT AROUND
		GRAY AREA
	GRAY AREA
	DO NOT	DO NOT
TAPE	CUT AROUND	CUT AROUND TAPE
HERE	GRAY AREA	GRAY AREA HERE

FOR CUTTING

Large white area

represents what to cut out for the speaker face.

On the template at right, small circles outside the white area indicate additional holes needed for the round-faced speaker only.

NOT FOR CUTTING

Large gray area

represents space to

reserve behind the wall

for the speaker

enclosure.

On the template at right, small gray tabs also indicate where not to cut.

A	E	WARNING: Make sure the spot chosen is safe for cutting.				T
	R	Do not cut through surfaces that have hazards, such as				APE
T	P E					HERE
	E	electrical wiring, conduits or plumbing, concealed behind
H		them. If you are not sure, consult a professional installer
		before you proceed.
			Translations below
	WARNING: Make sure the spot chosen is safe for cutting. Do not cut through surfaces that have hazards, such as electrical
	wiring, conduits or plumbing, concealed behind them. If you are not sure, consult a professional installer before you proceed.
		WARNING: Make sure the spot chosen is safe for		WARNING: Make sure the spot chosen is safe for
		drilling. Do not cut through surfaces that have hazards		drilling. Do not cut through surfaces that have hazards
		concealed behind them, such as electrical wiring,		concealed behind them, such as electrical wiring,
WHITECUT		conduits or plumbing. If you are not sure, consult a		conduits or plumbing. If you are not sure, consult a
		WARNING: Make	Pilot	Hole	WARNING: Make	OUTAREA
		professional installer before you proceed.		professional installer before you proceed.
OUTAREA		sure the spot chosen			sure the spot chosen	WHITECUT
		is safe for drilling. Do			is safe for drilling. Do
		not cut through			not cut through
		surfaces that have			surfaces that have
		hazards concealed			hazards concealed
		not sure, consult a			not sure, consult a
		behind them, such			behind them, such
		as electrical wiring,			as electrical wiring,
		conduits or			conduits or
		plumbing. If you are			plumbing. If you are
		professional installer			professional installer
		before you proceed.			before you proceed.
	WARNING: Make sure the spot				WARNING: Make sure the spot
	chosen is safe for drilling. Do not cut				chosen is safe for drilling. Do not cut
	through surfaces that have hazards				through surfaces that have hazards
	concealed behind them, such as				concealed behind them, such as
	electrical wiring, conduits or plumbing.				electrical wiring, conduits or plumbing.
	If you are not sure, consult a				If you are not sure, consult a
	professional installer before you				professional installer before you
	proceed.				proceed.
			English & Translations
TAPE						TAPE
HERE						HERE
		DO NOT			DO NOT
		CUT AROUND			CUT AROUND
		GRAY AREA			GRAY AREA
DO NOT					DO NOT
CUT AROUND					CUT AROUND
GRAY AREA					GRAY AREA
DO NOT					DO NOT
CUT AROUND					CUT AROUND
GRAY AREA					GRAY AREA
		DO NOT			DO NOT
TAPE		CUT AROUND		CUT AROUND		TAPE
HERE		GRAY AREA			GRAY AREA	HERE

CAUTION: When installed, the speaker enclosure cannot be seen behind the wall or ceiling. Do not attempt to nail, cut, or drill on that surface area. Puncturing the speaker enclosure with a tool will seriously damage the speaker.

•All electrical wiring, vents, and plumbing pipes located inside the walls must be avoided (Figure 8). Check with a trained professional if you need instructions on how to locate and avoid them.

Figure 8 (a) (b)

Cautions against unseen danger, such as (a) electri- cal wires or (b) plumbing pipes, behind the wallboard

•Use of a stud finder can help ensure that the speaker hole is at least 43/4" (12 cm) from a stud or joist.

•The selected location should be at the height you want for both speakers and where you can maintain the minimum distance of 5 feet (1.5 m) between them.

Keeping in mind the guidelines given:

1.Decide where the first speaker will go.

2.Select the location for the second speaker.

3.Use the provided template for drawing both a pilot hole and the speaker-face outline.

10 AM267565_01_V.pdf May 13, 2003