MASTER VOLUME
By default, the dial on the wired controller is the master volume control for the speaker system. Turn the dial clockwise to increase the volume and
NOTE: Three buttons on the wired controller have multiple functions. The primary function is written in white text. The secondary function is written in grey text.
1.Press and release a button to access its
2.As explained on the back of the wired controller, press and hold a button for a few seconds to access its
BASS
To adjust the bass level, press the bass/center button on the wired controller. The bass/center LED will light solidly. Turn the dial on the wired controller clockwise to increase the bass level and counter- clockwise to decrease the bass level. After a few seconds of inactivity, the bass LED will turn off.
TEST
To verify that all speakers are correctly connected and to reset volumes, press and hold the mode/test button on the wired controller for a few seconds. The test LED will flash on and off for a few seconds while an audio signal is sent to the front left speaker. This is repeated for the center, front right and rear speakers (the two rear speakers receive the signal simultaneously). While a speaker is being tested, you may turn the dial on the wired controller to adjust its relative volume. Turn clockwise to increase the speaker’s volume and counterclockwise to decrease the speaker’s volume.
RESET MASTER VOLUME AND
ADJUST RELATIVE VOLUMES
To reset the master volume and each speaker’s relative volume to default levels, press and hold the mode/test button on the wired controller for a few seconds.
NOTE: The XA3051 will remember your settings even if you turn if off or unplug it from the wall.
SYSTEM SPECIFICATIONS
| Total System Power: | 100 Watts (50 Watts RMS) |
| SUBWOOFER |
|
|
| Frequency Response: | 32 Hz – 18 kHz |
| Speaker Drivers: One 6.5" | ||
|
|
|
|
|
| |
| Signal to Noise Ratio @ 1 kHz input: > 76 dB |
|
|
|
| |
|
|
|
| POWER REQUIREMENTS |
|
|
| Crossover Frequency: | 150Hz |
|
|
| |
|
|
|
|
| ||
|
|
|
| USA/Canada/and applicable | 120 V AC @ 60 Hz | |
| System THD (distortion): | < 0.2 % THD @ |
| |||
|
|
|
|
| ||
|
| scale input voltage |
| Latin American countries: |
|
|
|
|
|
|
|
|
|
| Input Impedance: | 10k ohms |
|
|
|
|
|
| Europe/United Kingdom; | 230 V AC @ 50 Hz | |||
|
|
|
| |||
|
|
| ||||
| SATELLITE AMPLIFIED SPEAKERS |
|
| applicable Asian countries; |
|
|
| Drivers (per satellite): | One 3" |
| Argentina, Chile and Uruguay: |
|
|
|
|
|
|
| ||
|
|
|
| ETL / cETL / CE / NOM / IRAM Approved | ||
| Driver (per Center Speaker): | One 3" |
| |||
|
|
|
|
| ||
|
|
|
|
|
|
|
TROUBLESHOOTING TIPS
The answers to most setup and performance questions can be found in the Troubleshooting guide. You can also consult the FAQs in the customer support section of our Web site at www.alteclansing.com. If you still can’t find the information you need, please call our customer
TREBLE
To adjust the treble level, press the treble/rear button on the wired controller. The treble/rear LED will light solidly. Turn the dial on the wired controller clockwise to increase the treble level and counter- clockwise to decrease the treble level. After a few seconds of inactivity, the treble LED will turn off.
CENTER
To adjust the center speaker volume, press and hold the bass/center button on the wired controller for a few seconds. Center volume is represented by the bass LED. As a result, the bass/center LED will flash on and off when you are adjusting the volume of the center speaker. Turn the dial on the wired controller clockwise to increase the center speaker volume and counterclockwise to decrease the center speaker volume. After a few seconds of inactivity, the bass LED will turn off.
REAR
To adjust the rear speaker volume, press and hold the treble/rear button on the wired controller for a few seconds. Rear volume is represented by the treble LED. As a result, the treble/rear LED will flash on and off when you are adjusting the volume of the rear speakers. Turn the dial on the wired controller clockwise to increase the rear speaker volume and counterclockwise to decrease the rear speaker volume. After a few seconds of inactivity, the treble LED will turn off.
RESET BASS, TREBLE, CENTER AND REAR
To reset the bass, treble, center and rear controls to default levels, press and hold both the bass and treble buttons down at the same time for a few seconds.
NOTE: The XA3051 will remember your settings even if you turn if off or unplug it from the wall.
MODE
In the stereo mode, only the subwoofer,
In the surround mode, the Dolby Surround Pro Logic circuitry sends an audio signal to all six speakers.
By default, the XA3051 starts up in the surround listening mode. Pressing and releasing the mode/test button enables you to toggle between the stereo and surround listening modes.
3
service team for assistance before returning the speakers to your retailer under their return policy.
Customer service is available 7 days a week for your convenience. Our business hours are:
Monday to Friday: 8:00 a.m. to 12:00 midnight EST
Saturday & Sunday: 9:00 a.m. to 5:00 p.m. EST
Email: csupport@alteclansing.com
For the most
© 2002 Altec Lansing Technologies, Inc.
Designed and engineered in the USA and manufactured in our ISO9002 certified factory. United States Patents 4429181 and 4625328 plus other patents pending.
4