Loewe Auro 2216 PS manual Activate Digital Link, Switch over PAL/NTSC, Doing a reset

Page 12

First installation

DVD menu

Language DVD Player Menu

 

Deutsch

D

 

English

GB

 

Español

E

 

Français

F

 

Nederlands

NL

 

Italiano

I

 

Accept with OK

Info

 

 

Back

 

 

End

Press the button OK .

The selected language is then set as Auro’s user interface language.

The DVD menu is closed when you press the END button.

Activate Digital Link

With Digital Link, Loewe TVs pass on the remote control signals to Auro via the Euro-AV connection. Digital Link is useful when you want to install Auro con- cealed, e.g. in a closed rack where it cannot be reached by the remote control signals.

Switching on Digital Link

Auro must be in standby (standby indicator lights red, display is dark). Hold the

button the device pressed for at least five seconds until the message LINK appears in the display.

Switching off Digital Link

Auro must be in standby (standby indicator lights red, display is dark). Hold the

button the device pressed for at least five seconds until the message FRONT appears in the display.

Switch over PAL/NTSC

Auro is set to the PAL TV norm at the factory. If your TV is set to another standard (NTSC), you have to adapt the Auro setting accordingly. There is no disc in the drive and the drawer is closed.

If Auro is switched on: keep the Pause button on the device

or on the remote control pressed for five seconds.

NTSC, appears in the device display, Auro is then set to the NTSC TV standard. In the same way, you can set the Auro to AUTO or PAL.

In the AUTO AUTO setting, Auro automatically detects whether a PAL or an NTSC-DVD is inserted and switches over to the respective standard.

Doing a reset

You can reset all settings in Auro to their original values with a Reset. The state prior to initial installation (Factory Setting) is reinstated.

If Auro is in standby mode (red standby indicator lights) and the remote control is set to the DVD/CD mode:

1. Press the button on the remote control and hold it down.

. Also press the button on the device and hold it down.

3.Keep both the buttons held down for at least 5 seconds.

Then, Auro switches on, the message RESET appears in the display. The

sub-device DVD/CD is active.

All settings are therefore reset to their original values. You have to perform initial installation.

Switching over to Progressive Scan

With the Progressive Scan mode you get the highest possible picture quality without flickering in the “Component Video” operating mode. Set the “VIDEO OUT SELECTOR“ switch on the back of Auro to the “COMP“ position. If Auro is switched on: Keep the stop button (there is no disc in the drive and the drawer is

closed. / no menu display) on the unit pressed for five seconds. P-SCAN ON, appears in the unit display so that Auro is switched to Pro-

gressive Scan mode.

In the same way you can set Auro to P-SCAN OFF.

- 12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operating Manual Equipment Contents Switch over to operate TV set Switch over to operate Recorder+Volume down/up TV Sound off/onAuro 2216 PS Front Panel Auro 2216 PS Rear Panel & Display Set up WelcomeThank you Scope of deliveryCleaning For your safetyTechnical requirements for L-Link First installation Connecting antennaeTV interferes with AM reception when it is on ConnectionWiring Loewe Flat TV Auro Individual Sound/Tremo Audio cable cinch Scart Available in specialised TradeSurround speaker system Digital audio TV AuroWiring Auro audio system Remote controlInserting the batteries System to at least 100 HzSwitching on for the first time Setting the languagePower mains No disc in the driveSwitch over PAL/NTSC Doing a resetSwitching over to Progressive Scan Activate Digital LinkSetting the loudspeaker system Selecting the speaker systemConnect speakers Speaker SystemAdjust loudspeaker level Entering the distance between speakersDo the same for all connected speakers Press the button Press the button See the section on audio functions pgActivate the mode of the remote control About operationInserting a disc Basic functionsMenu and window Context helpTitle ChapterTitle Table Status displaySleep timer User interface of the inserted DVDNumeric input Automatic functionsPress button on remote control Or button on Auro Message Start playbackSelect title Press the green buttonSelect chapter Chapter forward or backSearch Pause single frameInterrupting playback Ending playbackExtended functions Selecting sound formatSubtitles Camera positionRepeat Zoom magnify imageUsing markers Play from …To move the magnified image section over the whole image Set other markersBasic settings SettingsSlow motion Picture FormatSpecial features of DVD Audio Setting Digital Sound OutputLanguages Presettings Page Audio-CD Play from … Hide status displayAudio-CDs with CD-Text CD RandomEnd CD Random function RepeatTitle Programming To switch on/off the Custom File function Save program Custom FileTo delete the inserted disk from the Custom File Select the item Delete from Custom FileMP3 and Jpeg MP3 and Jpeg mixedCD Text Menu bar MP3Folder/Title Table Title Programming/Custom FileKodak Picture CD Rotate Jpeg picturesChild Lock Activating the child lock for the first timeDetermine your personal identification number PIN Prompting the location of the setUsing the child lock Tuner Switching tuner display Fine tuningMono/Stereo switching Individual resortingVolume Tuner Audio functionsProgramming the station manually Treble and bassNight mode With the DVD menuGo to the item Treble or Bass SoundSetting the remote control Sound modeRemote control Assist TV-operation PIP on/off picture in pictureMenu Other functions on/off Station list on Menu confirm/callProblem Remedy What to do, ifTechnical Data Service
Top Page Image Contents