Maxtor pmn user manual Sensor Connection, Network Connection

TCP/IP SETUP

ALL ABOUT IMAGE RECOGNITION & PROCESSING

4. Installation

5) Sensor Connection

Connect the Sensor to the SENSOR INPUT/OUTPUT on the Rear Panel of the system

ALL ABOUT IMAGE RECOGNITION & PROCESSING

5. Operation

7. TCP/IP SETUP

TCP/IP option of this DVMR system enables user to see live pictures and recorded pictures via internet line, far apart from DVMR unit. To see live pictures or recorded pictures of DVMR, users must assign IP address into DVMR together with Gateway and Subnet mask first, and then install Remote Viewer

RELAY ALARM

D D C N N G D D D D -- + O C O N 4 3 2 1

M D

COM NC NO GND D4 D3 D2 D1

Terminal block

Pin 1	Alarm1
Pin 2	Alarm2
Pin 3	Alarm3
Pin 4	Alarm4
Pin 5	GND
Pin 6 NO( Normal Open )
Pin 7 NC( Normal Close)
Pin 8	COM

Program included in the package on client PC.

For detail procedure for installing Remote Viewer Program and setting up, refer to manual for Remote Viewer program included in the package.

1IP ADDRESS : Enter numbers using direction buttons and press [MENU] button.

TCP/IP SETUP

2GATEWAY : Enter numbers using direction

buttons and press [MENU] button.		IP ADDRESS	1
	SYSTEM SETUP	GATEWAY	2
3 SUBNET MASK : Enter numbers using		SUBNET MASK	3
		MAC ADDRESS	4
	DISPLAY SETUP	DHCP SETUP		5
direction buttons and press [MENU] button.	CAMERA TITLE
	TIME/DATE SETUP

Relay output : COM+NC, COM+NO OR COM+NC+NO

Alarm input : Short-circuit between Alarm1, Alarm2, Alarm3 or Alarm4 and GND is recognized as alarm.

NOTICE : Sensor input is RECOGNIZED as LOW when alarm signal is on a level with GND,

and it is recognized as HIGH when alarm signal is FLOATING or 5V. Following is internal circuit. 5

V

Internal Circuit D1

Thus, there is a danger of damage, when the sensor input goes to a Negative level or voltage higher than 5V.

6) Network Connection

RS-232C : Connect to PC to operate DVMR

RS 485 : Connect to PTZ camera

AUDIO : 1 audio input/channel, 1 audio output from selected channel.

RJ-45 (ETHERNET) : Connect to LAN, WAN or Internet

	FUNCTION
	1	RS 485 D-	6	ALARM GND
	2	RS 485 D+	7	ALARM D4	SPK		MIC4	MIC3		MIC2		MIC1
	3	RELAY COM 8		ALARM D3
	4	RELAY NC	9	ALARM D2				AUDIO					ETHERNET
PTZ	5	RELAY NO	10	ALARM D1
CAMERA			RS-232C
				1	2	3	4	5	6	7	8	9	10

For more details, refer to arrangements RS-232c pins in page 32.

7

4 MAC ADDRESS : It is unique ID number	ALARM/MOTION SETUP
provided by the manufacturer, and the user	RECORD SETUP
	TCP/IP SETUP	SELECT , PRESS ENTER
should not change under any condition.	MISCELLANEOUS
	FACTORY DEFAULT

5DHCP SETUP : In case you connect DVMR unit to LAN network under router/Gateway/IP

sharer which has DHCP server function, set DHCP SETUP at DHCP, and DVMR unit automatically gets IP data automatically during the process of booting.

In case you connect DVMR unit to leased line with static IP, Router/Gateway connected ADSL(with static IP or dynamic IP), you are requested to set DHCP at MANUAL and input IP data manually. For details, refer to Remote Viewer manual.

1) Concept of accessing to DVMR unit via IP network
										PTZ
		PC					DVMR unit			Camera
			LAN, WAN, or Internet
		Client program					TCP/IP setup
		(remote viewer)
2) Conditions of IP network
a) Accessing to DVMR unit in the same Intranet(LAN)								PC
		DHCP server				LAN	DHCP SETUP
		Router/Gateway					DVMR unit
		IP Sharer
							Automatic
b) Accessing to DVMR unit via Internet line
										DHCP SETUP
					Leased line w/ static IP
		PC	Internet							DVMR unit
					Cable modem w/ dynamic IP
		Client program
									Leased line : Manual
		(remote viewer)
									Cable modem : Automatic
					ADSL
										DHCP SETUP
					modem
		PC	Internet		w/			Router		DVMR unit
	Client program			dynamic IP				or
										Manual
	(remote viewer)			24	or			Gateway
									Other devices
					static IP
					PPPoE		Port Forwarding
					protocol		(IP Forwarding)

For details of TCP/IP setting in DVMR unit and PC, refer to “Remote Viewer manual” included in the package.

24