Jensen JCR-275 user manual Snooze Function, Listening to Radio, Sleep Timer Operations

Page 8

1.

Press the ALARM 1 (#7) or ALARM 2 (8) BUTTON to select the Music option ( ) for wake-to-

 

radio.

2.

Press the same button again to change to the Alarm option ( ) for wake-to-alarm.

3.

Press the same button again to disable the corresponding ALARM 1 or 2.

Turning Off the Alarm:

The alarm or radio will sound for 30 minutes unless interrupted by pressing the corresponding ALARM 1 or ALARM 2 BUTTONS or ON/OFF BUTTON (#5). It will repeat the chosen alarm again at the same time on the following day according to the weekday alarm settings described above.

SNOOZE FUNCTION

When the preset alarm time is reached, the chosen alarm will sound. You can momentarily stop the alarm sound for 9 minutes by using the snooze function.

Press the SNOOZE BUTTON (#3) for a 9 minute snooze duration during beep or radio alarm. During the Snooze delay, the alarm icon or will flash.

The Snooze function can be repeated within the alarm duration or 30 minutes from the original wake time.

If you set the DISPLAY DIMMER SWITCH (#12) to the Auto OFF Mode, the LED DISPLAY (#10) will turn off automatically after the snooze function is activated and then light again when the snooze duration has expired.

LISTENING TO RADIO

1.Choose between AM and FM bands by using the BAND SELECTOR BUTTON (#1).

2.Press the ON/OFF BUTTON (#5) to turn radio on.

3.Rotate the TUNING CONTROL (#19) to your desired radio station according to the dial scale on the unit.

4.Rotate the VOLUME CONTROL (#18) to adjust to the desired output level.

5.To turn off the radio, press the ON/OFF BUTTON (#5).

TIPS FOR BEST RECEPTION

AM – The AM antenna is located inside the cabinet of the unit. If AM reception is weak, change the position of unit until the internal antenna picks up the strongest signal.

FM – During FM reception, always keep the FM WIRE ANTENNA (#15) fully extended for best performance. However, if FM reception is weak, try repositioning the unit until you get the best reception.

SLEEP TIMER OPERATIONS

Setting sleep time while listening to radio:

1.Press the SLEEP BUTTON (#3) to activate the Sleep function. The default sleep time is 90 minutes and will flash for 5 seconds unless you change it.

2.Press the SLEEP BUTTON (#3) repeatedly to decrease the sleep time to 60, 30, 15 minutes or OFF.

USING THE AUX IN TO LISTEN TO EXTERNAL AUDIO PLAYER

You can playback your favorite music from your iPod or portable digital audio player using the Aux in function.

1.Connect the headphone jack of your external device to the AUX IN JACK (#17) located on the back of the unit using a stereo cord with a 3.5mm phone plug on either ends. (Note: the stereo cord is not included)

2.Press the ON/OFF BUTTON (#5) to turn on the radio. It will automatically switch to Aux In mode when a suitable stereo cord is correctly connected.

3.Start playing your external audio device.

4.Slowly increase the volume control of the unit until the desired level is obtained. To avoid output sound distortion due to overloading, you may need to lower the volume output of your audio device.

Note: the stereo music from your audio device will be converted to a monaural audio output.

E-7

Image 8
Contents AM/FM Dual Alarm Clock Radio with Wave Sensor Model JCR-275 Important Safety Instructions Compliance with FCC Regulations Protect Your Furniture Dear Jensen CustomerControls and Functions of Unit Power RequirementsLocation of Controls Setting UP the Calendar and Clock Getting StartedSetting UP the Time Zone Calendar and Temperature DisplaySetting UP the Alarms DST Daylight Saving TimeSleep Timer Operations Using the AUX in to Listen to External Audio PlayerSnooze Function Listening to RadioRadio on mode, to turn sleep function on While the alarm is sounding, to turn snooze function onInfrared Sensor Function Night Light Resetting the UnitDimmer Control Specifications Care and MaintenanceTroubleshooting Guide Symptom Possible Cause SolutionDAY Limited Warranty and Service Valid in the U.S.A only