Honeywell TN924W user manual Features, Battery Installation, Mounting, Placement, Operation

Page 4

REMOTE THERMO HYGROMETER SENSOR

FEATURES

•Remote data transmission to the main unit via 433 MHz signal

•328 feet (100 meters) operating range without interference

•LCD displays temperature, humidity and channel

•Five (5) transmission channels selection

•Case can be wall mounted using built-in hanger

A.LED INDICATOR

•Flashes once when the remote sensor transmits a reading to the main unit.

•Flashes twice when battery power is low.

B.BATTERY COMPARTMENT

Holds two AA-size batteries

C. RESET

Resets all previous settings

D. CHANNEL SWITCH

Selects the desired channel from 1 to 5

E. WALL-MOUNT RECESSED OPENING

Keeps the remote sensor on the wall

Note: Install the batteries and select the channel before mounting the sensor.

BATTERY INSTALLATION

•Remove the screws from the battery compartment with a small Phillips screwdriver.

•Set the channel 1 through 5. The switch is located in the battery

compartment. Channel 1 is typically selected if only one remote sensor is being used.

•Install 2 “AA” size alkaline batteries (not included) matching the polarities shown in the battery compartment.

•Replace the battery compartment door and secure the screws.

•Secure the thermo-hygrometer remote sensor in the desired location.

MOUNTING

•The remote thermo-hygrometer sensor can be placed on the flat surface or

7

mounted on the wall in vertical position

•Use the wall mount hardware and screws provided when mounting the thermo-hygrometer sensor on the wall

PLACEMENT

•The remote thermo-hygrometer sensor should be placed in the area with a free air circulation and sheltered from the direct sunlight and an extreme weather conditions.

•Ideally, place the thermo-hygrometer sensor above the natural surfaces (such as a grassy lawn).

•Avoid placing the thermo-hygrometer sensor near sources of heat such as chimneys and heating elements.

•Avoid any areas collecting and radiating a heat from the sun, such as metal, brick or concrete structures, paving, patios and decks.

•The international standard for the valid air temperature measurements is 4 feet (1.25meters) above the ground.

OPERATION

Immediately after batteries are correctly installed, the remote sensor will start transmitting a temperature and humidity data to the main unit.

RAIN GAUGE

FEATURES

•Precipitation measurement

•Remote transmission of the rainfall data to the main unit via 433 MHz signal

•Operating range of up to 100 feet (30 meters)

•Built-in installation level

•Non-corrosive protective screen

BA

C

A. Rain gauge bucket

Holds all rain gauge components

B.Knob

Secures the top on the rain gauge bucket

8

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Honeywell Weather Information Station TN924WStandard Package Contents IntroductionInstallation Before YOU BeginFeatures Battery InstallationPlacement MountingWind Vane Wind CupsAssembly Power TimeDisplay Front RearMain Display Unit Overview SideALARM/CHART Weather Station Controls PanelSET ChannelAbout the National Weather Radio System Weather RadioCustomizing Your Weather Radio Alerts Selection Press or selecting ADVISORY, Watch or WarningProgramming Your Location Multiple or Single optionTesting Your Weather Radio Signal Loss ReminderAlert Mode Selection Activating or Deactivating Audible AlertsWeather Station Navigating Through the ModesConnecting Weather Station to a Personal Computer Customizing Your Weather StationRain Window Wind WindowUsing Different Weather Station Windows Accessing Weather and Pressure WindowsViewing Pressure and Altitude Information Programming SEA Level PressureViewing PRESSURE, Temperature and Humidity BAR Charts Viewing Moon Phase History and Weather ForecastUnderstanding Moon Phase Icons Viewving SEA Level Pressure HistoryAccessing Time Window Activating or Deactivating AlarmsProgramming Alarms AUTO-PROGRAMMINGIcon Atomic Time Reception Strength To disable alarms SUNRISE/SUNSET WindowActivating or Deactivating Snooze Wwvb Radio Controlled TimeTemperature and Humidity Window Accessing Temperature and Humidity Window Viewing Remote Channel Temperature and HumidityRecalling Temperature and DEW Point Information Programming Temperature in Celsius or FahrengeitRain Window Wind WindowMaintanance Troubleshooting PrecautionsSymptom Solution WEATHER/SNOOZE isAppendix 1 City Codes US and Canadian CitiesAppendix 2 NWR Alert Messages DST Daylight Savings Time definitionsSpecifications Temperature IndoorRadio Frequency 433 MHz Barometric PressureTemperature remote Battery life alkaline Main unit around 24 hoursWeight without batteries DimensionsFCC Statement Standard Warranty InformationDeclaration of Conformity

TN924W specifications

The Honeywell TN924W is a state-of-the-art wireless thermostat designed to optimize home heating and cooling systems while ensuring energy efficiency and user convenience. This smart thermostat combines advanced technology with a user-friendly interface, making it an ideal choice for homeowners seeking to enhance their comfort while reducing energy consumption.

One of the main features of the TN924W is its Wi-Fi connectivity, allowing users to control their home temperature remotely through a smartphone app. The Honeywell Home app provides an intuitive platform for users to adjust heating and cooling schedules, monitor energy usage, and receive alerts, all from the convenience of their mobile devices. This capability not only increases comfort but also helps homeowners save on energy bills by enabling better management of heating and cooling patterns.

Another significant aspect of the TN924W is its compatibility with a wide range of heating and cooling systems. Whether it's a traditional HVAC setup, a heat pump, or a non-programmable system, the TN924W integrates seamlessly to deliver precise temperature control. This versatility ensures that users can enjoy the benefits of smart technology regardless of their existing system.

The TN924W also boasts a user-friendly touchscreen interface that simplifies programming and adjustments. With its clear display, users can easily navigate through the settings and customize their heating and cooling schedules. The thermostat supports multi-stage systems, allowing for more refined temperature management, which is particularly beneficial in larger homes or spaces with varying temperature needs.

In terms of energy-saving technology, the TN924W features Honeywell's Smart Response Technology. This innovative system anticipates heating and cooling needs based on various factors, such as current temperature, the time of day, and user habits, ensuring that the home is at the desired temperature when needed. Moreover, the thermostat can provide energy usage reports, empowering users with insights into their consumption patterns and opportunities for additional savings.

Overall, the Honeywell TN924W stands out as a leading choice for homeowners who prioritize comfort, convenience, and energy efficiency. Its advanced features, compatibility with diverse systems, and ease of use make it a valuable addition to any smart home.
Top Page Image Contents