La Crosse Technology WS-8025SU Oklahoma Texas, Oregon, Utah, Pennsylvania, Virginia, Puerto Rico

OK	Oklahoma	TX	Texas (cont.)
17K	Boise City	DFW	Dallas/Ft. Worth
LAW	Lawton	ELP	El Paso
OKC	Oklahoma City	HOU	Houston
TUL	Tulsa	LRD	Laredo
OR	Oregon	ODO	Odessa
BNO	Burns	SAT	San Antonio
EUG	Eugene	UT	Utah
MFR	Medford	SAL	Saline
PDX	Portland	SGU	St. George
SLE	Salem	SLC	Salt Lake City
PA	Pennsylvania	TSN	Thompson
CXY	Harrisburg	VA	Virginia
PHL	Philadelphia	DON	Vienna
PIT	Pittsburgh	LYH	Lynchburg
SCR	Scranton	ORF	Norfolk
PR	Puerto Rico	RIC	Richmond
SJU	San Juan	ROA	Roanoke
RI	Rhode Island	VT	Vermont
PVD	Providence	BTV	Burlington
SC	South Carolina	MPR	Montpelier
CHS	Charleston	WA	Washington
CUB	Columbia	ABE	Aberdeen
GMU	Greenville	ALW	Walla Walla
SD	South Dakota	KTF	Kettle Falls
FSD	Sioux Falls	MVN	Mt. Vernon
PIR	Pierre	OLM	Olympia
RAP	Rapid City	SEA	Seattle
TN	Tennessee	SFF	Spokane
BNA	Nashville	TON	Tonasket
CHA	Chattanooga	YKM	Yakima
DKX	Knoxville	WI	Wisconsin
MEM	Memphis	AUW	Wausau
TX	Texas	GRB	Green Bay
ABI	Abilene	LSE	La Crosse
AMA	Amarillo	MSN	Madison
AUS	Austin	MWC	Milwaukee
BRO	Brownsville	SSQ	Spooner

WV	West Virginia
CRW	Charleston
HLG	Wheeling
WY	Wyoming
BYG	Buffalo
CPR	Casper
CYS	Cheyenne
LAA	Little America
WYE	West Yellowstone

Canada City Listing

Code	City	Code	City	Code	City
EDM	Edmonton	YEL	Yellowknife	CHT	Charlotte Town
ALB	Calgary	OTT	Ottawa	MON	Montreal
VAN	Vancouver	SUD	Sudbury	QUE	Quebec
WIN	Winnipeg	THU	Thunder Bay	REG	Regina
FRE	Fredericton	TOR	Toronto	WHI	Whitehorse
HAL	Halifax
Mexico City Listings
Code	City	Code	City	Code	City
CHH	Chihuahua	MEX	Mexico City	HER	Hermosillo
DUR	Durango	GUA	Guadalupe

E.Time Zone and Daylight Saving Time Settings

1.Press and hold the "SET" button for 1 second.

2.Press and release the "SET" button 9 times.

3.The time zone will now flash based on the city selected.

4.Press and release the "+"or "-" button to adjust to the correct time zone.

5.Press and release the "SET" button to advance to the Daylight Saving Time setting.

6."dst ON" will now flash.

7.Press and release the "+" or "-" button to select DST 1 (recognizes Daylight Saving Time change) or DST 0 (does not change with Daylight Saving Time).

Note : Some locations (Arizona and parts of Indiana) do not follow Daylight Saving Time.

8.Press and release the "SET" button to advance to the weather measurement units settings (skip steps 1 and 2 in section E if continuing).

F. Weather measurement units (˚F/˚C, inHg/hPa)

1.Press and hold the "SET" button for 1 second.

2.Press and release the "SET" button 11 times.

3.The selected temperature units will now flash (˚F default/factory setting).

4.Press and release the "+"or "-" button to select ˚F (Fahrenheit) or ˚C (Celsius).

5.Press and release the "SET" button to advance to the barometric air pressure units setting.

6.The selected air pressure units will now flash (inHg default/factory setting).

7.Press and release the "+"or "-" button to select inHg (inches of Mercury) or hPa (hectopascal or millibars).

8.Press and release the "SET" button to advance to the barometric air pressure calibration setting.

9.The air pressure reading will now flash (29.91 inHg, 1012.8 hPa as default).

10.Press and release the "+"or "-" button to adjust to the correct relative air pressure based on local reports.

11.Press and release the "SET" button to advance to the forecast sensitivity setting.

Note : Barometric air pressure is usually reported as "relative air pressure". This reading is based on the combination of absolute air pressure and altitude. In general, an increase in altitude will result in a decrease in air pressure. Relative air pressure will make readings in nearby locations relative to each other to allow for proper forecasting. The absolute air pressure reading in the Weather Center cannot be calibrated, only the relative air pressure.

GB P.10 P.11 GB