Panasonic BTT268 Speaker installation option, Troubleshooting guide, General operation

Speaker installation option

Attaching to a wall

You can attach all of the speakers (except subwoofer) to a wall.

≥The wall or pillar on which the speakers are to be attached should be capable of supporting 10 kg (22 lbs) per screw. Consult a qualified building contractor when attaching the speakers to a wall. Improper attachment may result in damage to the wall and speakers.

≥Do not attempt to attach these speakers to walls using methods other than those described in this manual.

1 Drive a screw (not supplied) into the wall.

Troubleshooting guide

Before requesting service, please perform the following steps.

Do you have the latest firmware installed?

Firmware updates may be released to correct operating irregularities that are discovered with certain movies. ( 17)

4

Make the following checks and visit our website for more information.

http://www.panasonic.com/help

Enter the model number.

4

Or visit our website to find a service center.

AAt least 30 mm (1 3/16q) B ‰ 4.0 mm (5/32q)

C ‰ 7.0 mm to ‰ 9.4 mm (9/32q to 3/8q)

D Wall or pillar

E 5.5 mm to 7.5 mm (7/32q to 5/16q)

	
	

	

You can find a service center near you easily on our website.

Other support information:

“Customer Services Directory (United States and Puerto Rico)” ( 43)

The following do not indicate a problem with this unit: jRegular disc rotating sounds.

jImage disturbance during search.

2 Fit the speaker securely onto the screw(s) with the hole(s).

e.g., Front speaker

DO NOT	DO
≥ In this position, the	≥ Move the speaker so that
speaker will likely fall if	the screw is in this
moved to the left or right.	position.

Use the measurements indicated below to identify the screwing positions on the wall.

≥Leave at least 20 mm (25/32q) of space above the speaker and 10 mm (13/32q) on each side to allow enough space for fitting the speaker.

jImage disturbance when replacing 3D discs.

∫Unit does not respond to the remote

control or front panel buttons.

Press and hold [POWER Í/I] on the main unit for 5 seconds. jIf still unable to power the unit off, disconnect the power cord,

wait 1 minute, then reconnect the power cord.

∫Cannot eject disc.

The unit may have a problem.

While the unit is off, press and hold [9] on the remote control and [< OPEN/CLOSE] on the unit at the same time for more than 5 seconds.

General operation

To return to the factory preset

Front speaker, Surround speaker

F40 mm (1 9/16q) G 17.6 mm (11/16q) H 98.7 mm (3 7/8q)

Center speaker

I23 mm (29/32q)

J 95 mm to 97 mm (3 3/4q to 3 13/16q)

K 26 mm (1 1/32q) L 16.7 mm (21/32q) M 63.7 mm (2 1/2q)

 





		



≥Select “Yes” in “Restore Default Settings” in the Setup menu. ( 34)

To return all settings to the factory preset

≥Reset the unit as follows:

While the unit is off, press and hold [+ VOLUME], [< OPEN/ CLOSE] and [POWER Í/I] on the main unit at the same time for more than 5 seconds.

The remote control doesn’t work properly.

≥ Change the batteries in the remote control. ( 9)

≥The remote control and main unit are using different codes. If

“SET ” is displayed on the unit’s display when a button is pressed on the remote control, change the code on the remote control. ( 34)



VQT3M40

Disc cannot be played. ≥ The disc is dirty. ( 9)

≥Check the region code.

36