EMI S1C High Volt Electrical Wiring, Low Volt Interconnect wiring, Wiring must be at least 18 awg

Page 7

WLCA/WLHA HIGH WALL EVAPORATOR Installation Instructions

4.To access High and Low wiring remove the screw on the front of the control box.

High Volt Electrical Wiring

5.Refer to the wiring diagram to connect the power wire to Black L1 and the other wire to Red or White (115V) L2 at the power connector location.

6.Connect the ground wire to the ground

lug or lead at the same location in the control box.

Low Volt Interconnect wiring

for Unit mounted controls

The 24V control transformer is located in the evaporator. This provides low Volt control power to both the evaporator and condenser. Depending on the models se- lected, the low volt interconnect control wiring may be effected.

Ground

Low Voltage

L1

Connections

L2

 

!

Warning !

Note: All low volt interconnect

Be sure to keep any un-used wires

wiring must be at least 18 awg.

insulated with a wire nut or crimp.

 

Units With or without heat

Cooling only units utilize two low volt interconnecting wires between the indoor and outdoor units.

Wires designated “Y” (yellow) and “C” (brown) of the air handler should be con- nected to the corresponding “Y” (yellow) and “C” (brown) wires or terminals of the condenser. (See Figure 1A)

Other wires or terminals such as “R” (red) or “O” (orange) may not be needed and should be protected by a wire nut from making contact with the junction box or other metal surfaces.

Heat Pump Connection: In addition to the “Y” and “C” connections required for cool- ing, heat pumps require a reversing valve control wire “O” (orange) that is energized in the cooling mode.

If the indoor unit has an electric heater, then a ”W” (white) wire connection will also be needed to energize the indoor electric heat. If a remote thermostat is used.

Heat pumps models require an “R” connec- tion between the indoor and outdoor unit to provide power to the defrost control board in the condenser. (See Figure 1B)

WLCA/WLHA High Wall Evaporator

7

www.enviromaster.com

Image 7
Contents Installation, operation and maintenance Manual To the Installer Safety Instructions Anti-Short Cycle Compressor Pro- tection Day programmable with copy featureProduct Description Controls and ComponentsOptional Equipment Cabinet FeaturesInstaller Supplied Items WLCA/WLHA Controls and ComponentsWLCA/WLHA High Wall unit Mounting WLCA/WLHA Mounting preparationLocate Electrical Wiring WLCA/WLHA High Wall Evaporator Installation InstructionsElectrical Wiring Site Preparation Make sure power is offUnits With or without heat High Volt Electrical WiringLow Volt Interconnect wiring Wiring must be at least 18 awgChoosing a Remote Wall Mounted Straight CoolHeat pump connection Remote thermostat Two-stage Heating Piping Do’s and Don’ts Refrigerant PipingWLH24 Piston/Orifice Installation InstructionManifold Setup For Evacuation Charge to proper weight, charge WLCA/WLHA High Wall Evaporator User interface Buttons Quick Guide Configuration ModeControl User Interface instructions User interface Buttons Louver operation Mode of operationOn/Off Fan OperationOptional Heat pump with Electric heat 2-stage heating Sequence of Operation Unit Mounted key pad modeCool Mode Heat ModeSet Time Mode Dry ModeFilter Check Day Programming modePre-programmed run mode Manual runMin, 10 min, and 15 min Room Air Sampling Configuration ModeSequence of Operation Wall mounted thermostat mode Sleep timerChoosing a Thermostat Electric heat operation Cooling operationDrain Pan Sensor Other FeaturesShort Cycle Protection Asct LCD Back LightID coil sensor fault E03 Memory BackupRoom air sensor fault E01 Condensate fault E02Initial Start-up Optional Hand Held Controller programmingWLCA/WLHA Preperation for Start-Up Test Unit Performance Data Test Unit Performance Data sheetMaintenance Maintenance and Troubleshooting procedureEMI Air handlers with Unit Mount Infrared Controls TroubleshootingPower supply check Troubleshooting procedureOptional Heat pump With Electric Heat Low volt controlsCooling Only Units Electric HeatUnits with Condensation Pumps Display on the indoor unit is blank What should I do? Frequently asked questionsTroubleshooting procedure Mounting Tubing Model Depth Height Length WLCA/WLHA Physical DimensionsMedium Cabinet 18/24 WLCA/WLHA High Wall Evaporator SpecificationsWLCA/WLHA Electrical Specifications Small Cabinet 09/12Cooling Systems with S2CA Side discharge WLCA/WLHA System OptionsCooling Systems with Wall Units Heat pumps System Options with Wall UnitsSystem Options with T3CA TOP discharge System Options with T2CA TOP dischargeALL Product Limited Warranty Condensers EMI’s High Efficiency Product LineEvaporators High Wall Evaporator

WLHA, S1C specifications

The EMI S1C, also known as the WLHA, is a cutting-edge electronic device renowned for its advanced features and robust technologies. This innovative equipment caters to a wide range of applications, from multimedia processing to advanced communications. Its design showcases a seamless blend of functionality and performance, making it a preferred choice among professionals in various fields.

One of the standout characteristics of the EMI S1C is its high-performance processing capability. Equipped with a powerful multi-core processor, the device ensures rapid data processing and multitasking without compromising efficiency. This feature is particularly beneficial for applications requiring real-time data analysis and complex computational tasks.

The WLHA further distinguishes itself through its exceptional connectivity options. It supports multiple input and output standards, including USB, HDMI, and Ethernet, facilitating seamless integration with other devices. This flexibility allows users to connect a variety of peripherals and streamline workflows, enhancing overall productivity.

In terms of user experience, the EMI S1C places a strong emphasis on intuitive interaction. It features a user-friendly interface that simplifies navigation and accessibility. The touchscreen display provides responsive feedback, enabling users to operate the device effortlessly, even in high-pressure scenarios.

Another prominent aspect of the EMI S1C is its advanced power management system. The device is designed to optimize energy consumption without sacrificing performance. This sustainability feature is not only environmentally friendly but also crucial for mobile applications, where battery life is a significant consideration.

Furthermore, the WLHA's robust build quality ensures durability and resilience in diverse environments. The device is constructed with high-grade materials that withstand wear and tear, making it ideal for use in industrial settings or field operations where ruggedness is essential.

Security is also at the forefront of the EMI S1C's design. The device incorporates advanced encryption technologies and secure boot mechanisms to protect sensitive data from unauthorized access. This commitment to security is particularly relevant in today's digital landscape, where data breaches and cyber threats are prevalent.

In summary, the EMI S1C, WLHA is a versatile and powerful electronic device that excels in various domains. Its combination of high-performance processing, extensive connectivity, user-friendly interface, energy efficiency, durability, and robust security features makes it a top choice for professionals seeking reliability and innovation in their tools. Whether in multimedia, telecommunications, or industrial applications, the WLHA is poised to meet the demands of modern technology users effectively.