EMI WLHA, S1C manual Day Programming mode, Manual run, Pre-programmed run mode, Filter Check

Page 20

Sequence of Operation – Unit Mounted key pad mode

any mode including the Off mode. To en- ter the Set Time mode, press the “TIME” button in for three seconds. Pressing the “PROG” (NEXT) button will advance to the next item. The order is (1) Day of week, (2) Hour and (3) Minute. Pressing the “MODE” (BACK) button will return to the previous item. The time of day and day of week can be changed using the up or down arrow buttons.

When the “TIME” button is pressed again or left idle for 20 seconds, the con- trol shall save the new settings and return to the previous mode.

7-Day Programming mode

The 7-day programming mode is used to store the settings for the Pre-program Run mode.

When the unit is in either the Off or Run mode, the 7-Day Programming mode can be entered by pressing the “PROG” and “TIME” buttons simultaneously for three seconds. When the “PROG” and “TIME” buttons are pressed simultaneously again or left idle for 20 seconds, the control shall save the new settings and return to the previous interface mode.

While in the 7-Day programming mode, use the up or down arrows to change the time, temperature or period settings. Use the “MODE” (BACK) or “PROG” (NEXT) buttons to select the mode to be changed.

Settings for (1) Day of week, (2) Pe- riod of day, (3) Hour, (4), Minute, (5) Cool setpoint temperature, (6) Heat setpoint temperature and (7) Auto setpoint tem- perature can be entered.

Quick Copy

Quick copy is a feature of the 7-day programming mode. It is used to copy the settings of any day to the rest of the week. While in 7-day programming, select the day to be copied. Then, press the “FAN” and “PROG” buttons simultaneously for three seconds. The selected day will be copied to the rest of the week.

Manual run

This is normal operating (non pre-pro- gram run) mode. Settings for temperature, mode and fan speed are selected by the user and will not change with the passing of time. The word “PROGRAM” does NOT display on the LCD.

Pre-programmed run mode

This feature allows the setpoint tem- perature to be changed according to the pre-programmed set point and time of day settings. The setpoint and time settings are programmed into the control through the 7-day programming interface.

The Pre-programmed Run mode can be entered from Cool, Heat or Auto modes only. Pre-programmed run mode can- not be entered from Dry or Fan modes. Pressing the “PROG” button momentari- ly will enter or exit the Pre-program run mode. The word “PROGRAM” will appear in the LCD display. Then, with the pass- ing of time, the setpoint will change to the programmed setting at the time selected.

Filter Check

To aid in filter maintenance, the micro- processor will keep track of the units run time. Then, after the filter check time has elapsed, a “FILTER CHECK” warning will appear the LCD display. The filter check time is selectable through the configura- tion mode. Available settings are 250, 500, 750, 1000, and 1250 hours. Also if four evaporator freeze ups occur within a 24 hour period, (See fault condition E03) the filter check indicator will appear.

After filter maintenance has been per- formed, press the “MODE” and “FAN” but- tons simultaneously for three seconds to clear the filter check warning.

WLCA/WLHA High Wall Evaporator

20

www.enviromaster.com

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Installation, operation and maintenance Manual To the Installer Safety Instructions Day programmable with copy feature Product DescriptionControls and Components Anti-Short Cycle Compressor Pro- tectionCabinet Features Installer Supplied ItemsWLCA/WLHA Controls and Components Optional EquipmentWLCA/WLHA Mounting preparation WLCA/WLHA High Wall unit MountingWLCA/WLHA High Wall Evaporator Installation Instructions Electrical Wiring Site PreparationMake sure power is off Locate Electrical WiringHigh Volt Electrical Wiring Low Volt Interconnect wiringWiring must be at least 18 awg Units With or without heatStraight Cool Choosing a Remote Wall MountedHeat pump connection Remote thermostat Two-stage Heating Refrigerant Piping Piping Do’s and Don’tsPiston/Orifice Installation Instruction WLH24Manifold Setup For Evacuation Charge to proper weight, charge WLCA/WLHA High Wall Evaporator Quick Guide Configuration Mode User interface ButtonsControl User Interface instructions User interface Buttons Mode of operation On/OffFan Operation Louver operationSequence of Operation Unit Mounted key pad mode Cool ModeHeat Mode Optional Heat pump with Electric heat 2-stage heatingDry Mode Set Time ModeDay Programming mode Pre-programmed run modeManual run Filter CheckRoom Air Sampling Configuration Mode Min, 10 min, and 15 minChoosing a Thermostat Sleep timerSequence of Operation Wall mounted thermostat mode Cooling operation Electric heat operationOther Features Short Cycle Protection AsctLCD Back Light Drain Pan SensorMemory Backup Room air sensor fault E01Condensate fault E02 ID coil sensor fault E03WLCA/WLHA Preperation for Start-Up Optional Hand Held Controller programmingInitial Start-up Test Unit Performance Data sheet Test Unit Performance DataMaintenance and Troubleshooting procedure MaintenanceTroubleshooting EMI Air handlers with Unit Mount Infrared ControlsTroubleshooting procedure Power supply checkLow volt controls Cooling Only UnitsElectric Heat Optional Heat pump With Electric HeatUnits with Condensation Pumps Frequently asked questions Display on the indoor unit is blank What should I do?Troubleshooting procedure WLCA/WLHA Physical Dimensions Mounting Tubing Model Depth Height LengthWLCA/WLHA High Wall Evaporator Specifications WLCA/WLHA Electrical SpecificationsSmall Cabinet 09/12 Medium Cabinet 18/24WLCA/WLHA System Options Cooling Systems with Wall UnitsHeat pumps System Options with Wall Units Cooling Systems with S2CA Side dischargeSystem Options with T2CA TOP discharge System Options with T3CA TOP dischargeALL Product Limited Warranty EMI’s High Efficiency Product Line EvaporatorsHigh Wall Evaporator Condensers

WLHA, S1C specifications

The EMI S1C, also known as the WLHA, is a cutting-edge electronic device renowned for its advanced features and robust technologies. This innovative equipment caters to a wide range of applications, from multimedia processing to advanced communications. Its design showcases a seamless blend of functionality and performance, making it a preferred choice among professionals in various fields.

One of the standout characteristics of the EMI S1C is its high-performance processing capability. Equipped with a powerful multi-core processor, the device ensures rapid data processing and multitasking without compromising efficiency. This feature is particularly beneficial for applications requiring real-time data analysis and complex computational tasks.

The WLHA further distinguishes itself through its exceptional connectivity options. It supports multiple input and output standards, including USB, HDMI, and Ethernet, facilitating seamless integration with other devices. This flexibility allows users to connect a variety of peripherals and streamline workflows, enhancing overall productivity.

In terms of user experience, the EMI S1C places a strong emphasis on intuitive interaction. It features a user-friendly interface that simplifies navigation and accessibility. The touchscreen display provides responsive feedback, enabling users to operate the device effortlessly, even in high-pressure scenarios.

Another prominent aspect of the EMI S1C is its advanced power management system. The device is designed to optimize energy consumption without sacrificing performance. This sustainability feature is not only environmentally friendly but also crucial for mobile applications, where battery life is a significant consideration.

Furthermore, the WLHA's robust build quality ensures durability and resilience in diverse environments. The device is constructed with high-grade materials that withstand wear and tear, making it ideal for use in industrial settings or field operations where ruggedness is essential.

Security is also at the forefront of the EMI S1C's design. The device incorporates advanced encryption technologies and secure boot mechanisms to protect sensitive data from unauthorized access. This commitment to security is particularly relevant in today's digital landscape, where data breaches and cyber threats are prevalent.

In summary, the EMI S1C, WLHA is a versatile and powerful electronic device that excels in various domains. Its combination of high-performance processing, extensive connectivity, user-friendly interface, energy efficiency, durability, and robust security features makes it a top choice for professionals seeking reliability and innovation in their tools. Whether in multimedia, telecommunications, or industrial applications, the WLHA is poised to meet the demands of modern technology users effectively.
Top Page Image Contents