Bard P1224A1 Troubleshooting ECM Blower Motors, ∃ Run Mositure Check, Evidence of Moisture

Page 25

TROUBLESHOOTING ECM BLOWER MOTORS

CAUTION

Disconnect power from unit before removing or replacing connectors, or servicing motor. Wait at least 5 minutes after disconnection power before opening motor.

SYMPTOM

Motor rocks slightly when starting.

Motor won't start

∃No movement

∃Motor rocks, but wo'nt start

Motor oscillates up and down while being tested off of blower

∃Noisy blower of cabinet

∃"Hunts" or "puffs" at high CFM (speed)

CAUSE / PROCEDURE

∃This is normal start-up for ICM

∃Check power at motor

∃Check low voltage (24 VAC R to C) at motor

∃Check low voltage connections (G, Y, W, R, C) at motor

∃Check for unseated pins in connectors on motor harness

∃Test with a temporary jumper between R - G

∃Check motor for tight shaft

∃Run Mositure Check

∃Check for loose or compliant motor mount

∃Make sure blower wheel is tight on shaft

∃It is normal for motor to oscillate with no load on shaft.

∃Check for loose blower housing, panels, etc.

∃High static creating high blower speed?

–Check for air whistling through seams in ducts, cabinets or panels.

–Check for cabinet / duct deformation

∃Does removing panel or filter reduce "puffing"?

–Reduce restiction

–Reduce maximum airflow

Evidence of Moisture

∃Motor failure of malfunction has occured and moisture is present

∃Evidence of moisture present inside air mover

DO

∃Check out motor, controls, wiring and connections thoroughly before replacing motor

∃Orient connectors down so water ca'nt get in; install "drip loops"

∃Use authorized motor and control model numbers for replacement

∃Keep static pressure to a minimum:

–Recommend high efficiency, low static filters

–Recommend keeping filters clean

–Design duct work for minimum static, maximum comfort

–Look for and recommend duct work improvement,where necessary, in replacement.

∃Replace motor and perform Moisture Check

∃Perform Moisture Check

DON'T

∃Automatically assume the motor is bad

∃Locate connectors above 7 and 4 o'closk postions

∃Replace one motor of control model number with another (unless an authorized replacement)

∃Use high pressure drop filters. Some have 1/2" H2O drop!

∃Use restricted returns

Manual 2100-353 Page 23

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Installation Instructions Single Package AIR Conditioners Contents For More INFORMATION, Contact These Publishers Getting Other Information and PublicationsGeneral Instructions Field Installed Heater Packages OptionalShipping Damage GeneralHz Circuit a Electrical SpecificationsCompressor Circuit a Fan Motor and Condenser414 12.8 Volts Model Phase Heater Package Volts Model PhaseP1236A1-B This columnHtr. KW Circuit B Capacity @ 240 Volts @ 208 Volts Optional Field Installed Electric Heater TableHtr. Amps Fuses Circuits Ampacity Protection SizeDimensions of Units Typical Installations InstallationLocation Slab Mounting AT Ground Level Airflow and Service Access ClearancesElevated Mounting Platforms Roof TOP ApplicationMIS-1177C Unit Model Roof Hood Dimension Dimension for X in FIGRoof Curb Details Field Fabricated CurbingAIR Filters Condensate Drain TrapFilter Requirements & Sizes Condensate Drain TrapWiring 24V LOW Voltage Control Circuit Wiring Main PowerTransformer Taps ThermostatsLOW Voltage Wiring Start UP and Operation LOW Pressure SWITCH, BYPASS, and Lockout Sequence AdjustmentsAlarm Output Adjustable DELAY-ON-MAKE and DELAY-ON-BREAK TimerService Hints Service and TroubleshootingPressure Service Ports FAN Blade SettingsSuction and Discharge Tube Brazing Brazing DiagramIndoor Blower Perfomance ESP P1124A2 P1130A2 P1136A2 P1142A3 P1148A2 P1060A1Return Air Pressure 100 105 110 115 Model Pressure TablePressure Table Motor rocks slightly when starting Motor wont start Troubleshooting ECM Blower Motors∃ Run Mositure Check Evidence of MoistureExcessive noise Motor starts but runs erratically∃ Perform Moisture Check

P1230A1, P1124A2, P1148A2, P1236A1, P1248A2 specifications

The Bard P1136A2, P1242A1, P1130A2, P1224A1, and P1248A2 are high-performance industrial filtration systems renowned for their efficiency and advanced technologies. Ideal for various applications, including air, water, and process fluid filtration, these systems have become essential tools in a multitude of industries.

The Bard P1136A2 features a robust design that emphasizes durability and reliability. Equipped with high-efficiency particulate air (HEPA) filters, it substantially reduces airborne contaminants, making it suitable for cleanroom environments and laboratories. Its advanced monitoring system alerts users when filters need replacing, ensuring optimal performance at all times. The P1136A2 is also designed for easy maintenance, allowing quick access to components without extensive downtime.

Similarly, the Bard P1242A1 offers a distinctive combination of high filtration efficiency and low operational costs. Its multi-stage filtration process employs activated carbon to remove volatile organic compounds (VOCs) and odors. This system is particularly beneficial in industrial settings where air quality is paramount. The P1242A1 is designed with energy-saving technology, resulting in lower energy consumption without compromising filtration performance.

The Bard P1130A2 stands out with its compact design, making it an ideal choice for facilities with limited space. Despite its size, it delivers powerful filtration capabilities, utilizing an advanced pleated filter technology that maximizes surface area while minimizing resistance. This feature ensures long filter life and reduces maintenance frequency, translating to cost savings for end-users.

The Bard P1224A1 is characterized by its versatile applications and ease of integration with existing systems. Its modular design allows customization based on specific industrial requirements, making it suitable for diverse environments. Incorporating smart technology, the P1224A1 provides real-time monitoring and analytics, enabling proactive maintenance and enhancing operational efficiency.

Lastly, the Bard P1248A2 showcases cutting-edge design focusing on sustainability. Its energy-efficient components are coupled with eco-friendly materials, reducing the carbon footprint associated with filtration processes. This system is designed for industries aiming for compliance with environmental regulations while maintaining high performance and reliability.

Collectively, these Bard filtration systems epitomize technological advancement, offering unique features tailored to meet modern industrial challenges. Their focus on efficiency, sustainability, and user-friendly designs positions them as leaders in the filtration market, ensuring cleaner environments for all applications.
Top Page Image Contents