Lincoln Electric SVM186-A service manual Static SCR Test, Test Description

Page 61

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

F-21

TROUBLESHOOTING AND REPAIR

F-21

 

 

STATIC SCR TEST

WARNING

Service and repair should be performed by only Lincoln Electric factory trained personnel. Unauthorized repairs performed on this equipment may result in danger to the technician or machine operator and will invalidate your factory warranty. For your safety and to avoid electrical shock, please observe all safety notes and precautions detailed throughout this manual.

If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, contact the Lincoln Electric Service Department for electrical trou- bleshooting assistance before you proceed. Call 1-888-935-3877.

TEST DESCRIPTION

This procedure is a quick check to determine if an SCR is shorted or “leaky”. See machine waveform section for normal and abnormal SCR waveforms.

MATERIALS NEEDED

Volt/Ohm Meter (Analog)

PRECISION TIG® 225 Wiring Diagrams 3/8” nutdriver

SCR Heat Sink Assembly Drawing

PRECISION TIG® 225

Page 60 Page 62
Image 61
Page 60 Page 62
Contents Precision TIG ISAFETYi Fumes and Gases SafetyFor Electrically Powered equipmentSûreté Pour Soudage a LʼArc Précautions DE SûretéElectromagnetic Compatibility EMC Safety Master Table of Contents for ALL Sections Table of Contents Installation Section Input Single Phase only InstallationK2533-2 Input at Rated Output Model Height Width Depth WeightSelect Suitable Location Mounting Safety PrecautionsLifting and Moving TiltingInput and Grounding Connections Return Section TOC Input Reconnect ProcedureConnections for Stick Smaw Welding Connections for TIG Gtaw WeldingPrecision TIG Table of Contents Operation Section Operation Recommended Processes and EQUIP- Ment Product DescriptionControl Functionality Figure B.1 Control PanelPOWER-UP Sequence Machine Rating Plate Case Rear ComponentsOperating Steps Welding in TIG ModePulse TIG Control Operation Turn the power switch to on Welding in Stick ModePrecision TIG Table of Contents Accessories Section Standard Equipment Packages AccessoriesTable C.1 Table C.2 Factory Installed OptionsK2348-1 Under-Storage Cart Field Installed OptionsTable of Contents Maintenance Section Safety Precautions MaintenanceRoutine and Periodic Maintenance Spark GAP Adjustment1TABLE of CONTENTS-THEORY of Operation Section E-1 Theory of Operation Input Power CircuitGeneral Description Protected Output Rectification Feedback ControlFigure E.2 High Voltage/High Frequency Circuit High Voltage / High Frequency CircuitFigure E.5 DC Welding Current Generation DC Welding OutputFigure E.6 AC Square Wave Welding Current Generation AC Welding OutputFigure E.7 SCR Operation SCR OperationThermal Protection Protective CircuitsOverload Protection VAC Receptacle1TABLE of Contents Troubleshooting and Repair F-1 HOW to USE Troubleshooting Guide Troubleshooting and RepairWorkstations PC Board Troubleshooting ProceduresPerform the T1 Transformer Amptrol is depressed Troubleshooting and Repair Perform the SCR Bridge Test Possible Areas Misadjustments Problems SymptomsRecommended Course of Action Troubleshooting and Repair Troubleshooting and Repair Problems Symptoms Electric Shock can Perform the SCR Bridge Test Stick electrode Blasts Off when Weld current may be set too Test Description High Frequency Circuit Disable ProcedureMaterials Needed Figure F.1 Spark GAP Assembly ProcedureT1 Transformer Test T1 Transformer Test Primary Windings Primary Voltages Precision TIG Static SCR Test Precision TIG 225 Control Test ProcedureCase Cover Removal and Replacement Procedure Precision TIG Active SCR Test Active SCR Test Figure F.6 SCR Gate Locations Precision TIG Scope Settings Normal Open Circuit Voltage Waveform AC TIG ModeNormal Open Circuit Voltage Waveform DC TIG Mode Normal Open Circuit Voltage Waveform AC Stick Mode Normal Open Circuit Voltage Waveform DC Stick Mode Typical Output Voltage Waveform Machine Loaded AC TIG ModeMachine Loaded to 180 Amps AT 16VDC DC TIG Mode Machine Loaded to 180 Amps AT 26VDC AC Stick ModeDC Stick Mode Troubleshooting and Repair Precision TIG SCR Bridge Assembly Removal and Replacement Procedure Figure F.7 Case Back Mounting Screws SCR Bridge AssemblyProcedure Plug J2 Removed Replacement Procedure Precision TIG Polarity Switch Removal and Replacement Procedure Removal Procedure Polarity SwitchReplacement Procedure Precision TIG High Voltage Transformer Removal and Replacement Procedure Transformer Secondary Leads High Voltage TransformerFigure F.12 High Voltage Transformer Mounting Insulators Precision TIG 53F-53 Perform the SCR Bridge Assembly Replacement Procedure Input Idle Amps Retest After RepairRecommended Meters for Machine Output Tests Precision TIG Table of Contents Diagram Section Electrical Diagrams Schematic Complete Machine ALL Codes G5647 Schematic Control PC Board #1 G5640 Schematic Control PC Board #2 G5640 Schematic Control PC Board #3 G5640 PC Board Assembly Control #1 G5641 PC Board Assembly Control #2 G5641 1B0-S22530 PC Board Assembly Bypass L10121

SVM186-A specifications

The Lincoln Electric SVM186-A is a versatile and highly efficient welding machine that stands out in the competitive landscape of industrial welding equipment. Designed to meet the needs of both professionals and hobbyists, this machine combines advanced technology with robust construction, delivering outstanding performance in various welding applications.

One of the standout features of the SVM186-A is its multi-process capability. This welding machine can handle MIG, TIG, and Stick welding processes, making it suitable for a diverse range of projects, from light fabrication to heavy-duty work. This flexibility reduces the need for multiple machines, saving time and space for users who require versatility in their welding operations.

The SVM186-A is powered by a reliable and durable inverter technology, which ensures a stable arc and efficient operation across different materials, including stainless steel, aluminum, and mild steel. This inverter technology not only enhances performance but also reduces energy consumption, making it an environmentally friendly choice.

Another notable characteristic of the SVM186-A is its user-friendly interface. The digital display provides real-time information on voltage and wire feed speed, allowing welders to easily adjust settings for optimal results. This intuitive control panel design makes it accessible for both novice welders and seasoned professionals who value precision.

The machine is also built with safety features in mind. It comes equipped with overcurrent protection and thermal overload protection to prevent damage during operation. This ensures that users can work confidently, knowing that the equipment is designed to handle demanding tasks while prioritizing safety.

Portability is another advantage of the SVM186-A. Weighing in at a relatively light weight compared to other industrial welders, this machine is designed for ease of transport. Whether working on-site or in a workshop, welders can easily move the equipment as needed.

In summary, the Lincoln Electric SVM186-A is a sophisticated welding machine that merges technology and practicality. Its multi-process capability, inverter technology, user-friendly interface, safety features, and portability make it a top choice for those seeking dependable and efficient welding solutions. Whether for professional fabrication or personal projects, the SVM186-A is equipped to handle the demands of modern welding tasks with exceptional ease and effectiveness.
Top Page Image Contents