Lincoln Electric SVM176-A service manual 12TROUBLESHOOTING and REPAIRF-12, Feed Head Test

Page 40

Return to Section TOC

Return to Master TOC

F-12TROUBLESHOOTING AND REPAIRF-12

FEED HEAD TEST (cont.)

FIGURE F.3

Return to Section TOC

Return to Master TOC

539

LN-23P 541

Control

Board

539

541

POS

12Volt Supply

NEG

DC

AMPS

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

TEST PROCEDURE

1. Remove the weld wire from the drive rolls.

2. Disconnect the motor leads, 541 and 539, from the Control Board and clamp an amp probe around one of the leads.

NOTE: A DC ammeter may be connected in series with a motor lead if a current probe is not available.

3. Connnect a 12 VDC supply to the motor leads - Positive to lead 541 and Negative to lead 539.

The drive rolls should turn and run smoothly and the motor current should be less than 1amp. If so the feed head is OK.

If the drive rolls do not turn, and the ammeter shows no current, check the brushes for excessive wear. Insure that they move freely in the brush holders and are contacting the armature.

LN-23P

If drive rolls do not turn but the ammeter indicates current flow. remove the motor from the gearbox and repeat the test.

If the motor still does not run it is defective. If it runs properly there is probably something wrong in the gearbox.

If the drive rolls turn but not smoothly check the motor and brushes as indicated. If OK replace the gearbox.

Image 40
Contents Safety Depends on You LN-23PSafety Powered equipmentFor Engine Electric Magnetic FieldsFumes and Gases Electric Shock can kill ARC Rays can burnCan be dangerous Cylinder may explode Cause fire or explosion If damagedFor Electrically IiiPrécautions DE Sûreté Précautions DE Sûreté PourLES Machines À Souder À Transformateur ET ÀMaster Table of Contents for ALL Sections Table of Contents Installation Section Technical Specifications LN-23P InstallationEnvironmental Rating Safety Precautions Input CableWork Cable and Remote Voltage Sensing Work LeadOptional Features Installation Wire Drive Rolls and Guide TubesInnershield GUN and Cable Accessories Power SourceLN-23P Operation Section Table of ContentsOperation Section B Operation Loading the Wire ReelProduct Description Adjusting Wire Feed Speed Drive Roll PressureVoltage Making the WeldLN-23P Accessories Section Accessories Section CEnclosed Wire Reel Support Optional EquipmentGUN and Cable Assemblies K350 Adapter KITMaintenance Section Maintenance Section DMaintenance GUN and Cable MaintenanceWire Drive Assembly Maintenance Removing Idle Roll AssemblyCircuit Protection NameplatesLN-23P Theory of Operation Section Section E E-2E-2E-3E-3E-3E-4Theory of Operation Input Power CircuitGeneral Description Figure E.3 Control Circuits Optional Circuits K350 / K350-1ADAPTER KitsK350 / K350-1ADAPTER Kits LN-23P Troubleshooting and Repair Section F Troubleshooting and RepairSection F-1 How To Use Troubleshooting Guide Important Troubleshooting TipsPC Board Troubleshooting Procedures Troubleshooting & RepairElectric Shock Gun Perform Potentiometer Test K350 Adapter Problems Call LN-23PTest Description Wire Feeder TestMaterials Needed Wire Feeder Test Test ProcedureGUN Test 10TROUBLESHOOTING and REPAIRF-10 GUN TestFeed Head Test 12TROUBLESHOOTING and REPAIRF-12 Feed Head TestPotentiometer Test Wire Speed Control Potentiometer 14TROUBLESHOOTING and REPAIRF-14Potentiometer Test K350-1 Adapter Test 16TROUBLESHOOTING and REPAIRF-16 K350-1 Adapter TestMeasurement Points Expected Reading 18TROUBLESHOOTING and REPAIRF-18 Calibration CheckElectrical Diagrams Section G Electrical Diagrams SectionSection G-1 Electrical Diagrams Wiring Diagram Entire Machine M14197Schematic Entire Machine L6518 Wiring Diagram K350 Adapter KIT M14247 Wiring Diagram K350-1 Adapter KIT M17514 Machine Schematic for K350/K350-1 Adapter PC Board Assembly for Codes below 10892 G1528-4 PC Board Assembly for Codes 10892 and Higher G4184-3 Schematic for LN-23P Codes 10892 and Higher L11838-3

SVM176-A specifications

The Lincoln Electric SVM176-A is a robust and versatile semiautomatic wire feeder designed to cater to a wide range of welding applications. Known for its reliability and ease of use, the SVM176-A is particularly favored in both industrial and construction settings, where efficiency and performance are paramount.

One of the standout features of the SVM176-A is its compact design. This relatively lightweight unit is easy to transport and can fit into tight spaces, making it an ideal choice for mobile applications or projects that require more maneuverability. The unit's construction is durable and built to withstand the rigors of demanding work environments, ensuring longevity and consistent performance.

The SVM176-A supports various welding processes, including MIG (Metal Inert Gas) and flux-cored arc welding, providing versatility for different materials and thicknesses. This adaptability is enhanced by its ability to accommodate a variety of wire sizes, allowing users to select the ideal wire type for their specific project requirements. The equipment also features adjustable wire feed speed, helping to ensure optimal weld quality by allowing operators to tailor their settings based on the needs of the job.

Innovative technologies in the SVM176-A contribute to its performance. The unit is equipped with a digitally controlled microprocessor that streamlines operations, providing enhanced control over welding parameters. This advanced technology enables users to achieve precise welds consistently, minimizing the risk of defects and improving overall efficiency.

Another remarkable characteristic of the SVM176-A is its user-friendly interface. The unit features easy-to-read displays and intuitive controls, enabling operators to make quick adjustments without having to consult an extensive manual. This is particularly beneficial in fast-paced work environments where time is of the essence.

Furthermore, the Lincoln Electric SVM176-A boasts a range of safety features, including thermal overload protection and a sturdy casing, which safeguard both the equipment and the operator. With these characteristics combined, the SVM176-A stands out as a preferred choice for professional welders seeking reliability, versatility, and operational excellence in their equipment. This exceptional wire feeder continues to uphold Lincoln Electric's commitment to quality and performance in welding technology.