Lincoln Electric IM311-E manual Circuit Protection Nameplates, Power Source

Page 16

D-2

 

MAINTENANCE

D-2

 

 

 

 

CIRCUIT PROTECTION

NAMEPLATES

 

Circuit Breaker – The 3.5 amp circuit breaker located on the rear of the unit normally trips only when an overload occurs because of excessive loading in the wire feed cable or a defective motor or control compo- nents. After allowing a few minutes for cooling, push the reset button and weld. If it trips again, be sure the gun cable is not being excessively bent, is clean, and is the proper size for the wire diameter being fed. If it still trips, look for a defective electrical component.

POWER SOURCE

Whenever routine maintenance is performed on this machine — or at least yearly — inspect all name- plates and labels for legibility. Replace those which are no longer clear. Refer to the parts list for the replacement item number.

One or two LN™-23P’s can be connected to a DC power source (constant voltage) with a K-350 or K350-1 Adapter Kit. If two LN™-23P’s are connected, they can be set for different procedures but only one can be used at a time.

LN™-23P/ Power Source Combinations

1.Classic II, Classic III, Classic IIID, or SA-250 with K350-1 Adapter Kit and K623-1 Wire Feed Module.

2.Commander 300, Commander 400 or Commander 500 with K350-1 Adapter Kit.

3.Ranger 250 , Ranger 275, or Ranger 305G with K350-1 Adapter Kit.

4.CV-300, CV305, CV-400, DC-400, DC-600, DC655 or V300, V350 Pro, V450 Pro with K350-1 Adapter Kit.

NOTE: The K350 must be used on power sources with terminal strip connections only.

K316L-2 may not require a K350-1 adapter if the power source has a Lincoln 14 pin connector.

5.SAE-400 or SAE-400 Weld ’N Air with K316L-2, K385-2 CV Adapter & K2379-1 Adapter Kit. NOTE: Only allows for one LN™-23P feeder.

Gun will always be HOT when SAE-400 is running.

6.SAE-400 with a K385-1 and a K350 Adapter.

NOTE: K350 wii have to be powered from 120VAC receptacle (customer responsibility). No remote control of weld voltage from LN™-23P

Gun will always be HOT when SAE -400 is running

7.LN™-23P (K316L-2) used with V350-Pipe does not require a K350-1 Adapter.

Power source connection diagrams:

M17323

M14272

S25869

S25149

LN™-23P

Page 15 Page 17
Image 16
Page 15 Page 17
Contents LN -23P Safety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion Précautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Table of Contents Technical Specifications LN-23P InstallationEnvironmental Rating Input Cable Safety PrecautionsWork Cable and Remote Voltage Sensing Work Lead Optional Features Installation Wire Drive Rolls and Guide TubesInnershield GUN and Cable Operation Loading the Wire ReelProduct Description Instructions for Loading Wire Into LN-23P For machines that have code numbers Higher than Drive Roll Pressure Adjusting Wire Feed Speed and Voltage Making the Weld Accessories Enclosed Wire Reel SupportOptional Equipment GUN and Cable AssembliesMaintenance Removing Idle Roll AssemblyGUN and Cable Maintenance Wire Drive Assembly MaintenancePower Source Circuit Protection NameplatesTroubleshooting HOW to USE Troubleshooting GuideContact your local Lincoln Authorized Field Service Facility Troubleshooting Diagrams LN-23P Adapter KIT Wiring DiagramWiring Diagram LN-23P Wiring Diagram Connection of CV Converter to LN-23P’S and SA-200 or SA-250 14269 Connection of LN-23P and Adapter KIT to R3S-250 or R3S-325 Connection of LN-23P and Adapter KIT to R3S-400, 600 or 14272 Diagrams Diagrams Diagrams 12DIAGRAMS 17124 2-19-82MField Calibration of K-316 LN-23P P.C. Board Precaucion Warnung
Top Page Image Contents