Lincoln Electric IM10064 manual Safety Precautions, VRD Voltage Reduction Device

Page 12

A-2

INSTALLATION

A-2

 

 

 

SAFETY PRECAUTIONS

WARNING

Do not attempt to use this equipment until you have thoroughly read the engine manufacturerʼs manual supplied with your welder. It includes important safety precautions, detailed engine starting, operating and maintenance instructions, and parts lists.

------------------------------------------------------------------------

ELECTRIC SHOCK can kill.

•Do not touch electrically live parts or electrode with skin or wet clothing.

•Insulate yourself from work and ground

•Always wear dry insulating gloves.

------------------------------------------------------------------------

ENGINE EXHAUST can kill.

• Use in open, well ventilated areas or vent exhaust outside.

------------------------------------------------------------------------

MOVING PARTS can injure.

•Do not operate with doors open or guards off.

• Stop engine before servicing.

•Keep away from moving parts.

------------------------------------------------------------------------

See additional warning information at front of this operatorʼs manual.

Only qualified personnel should install, use, or service this equipment.

VRD (VOLTAGE REDUCTION DEVICE)

The VRD reduces the OCV (Open Circuit Voltage) at the welding output terminals while not welding to less than 20V DC when the resistance of the output circuit is above 200Ω (ohms).

This feature provides additional safety in environments with a higher risk of electric shock such as wet areas and hot humid sweaty conditions.

When VRD is “On” the DOWNHILL PIPE mode is not available.

The VRD requires that the welding cable connections be kept in good electrical condition because poor connections will contribute to poor starting. Having good electrical con- nections also limits the possibility of other safety issues such as heat-generated damage, burns and fires.

The machine is shipped with the VRD switch in the “On” position. To turn it “On” or “Off”.

•Turn the engine “Off”.

•Disconnect the negative battery cable.

•Lower the control panel by removing 4 front panel screws. (See Figure A.1)

•Place the VRD switch in the “On” or “Off” position. (See Figure A.1)

With the VRD switch in the “On” position, the VRD lights are enabled.

FIGURE A.1

(VRD)-VOLTAGE REDUCTION DEVICE SWITCH IS LOCATED IN THIS AREA.

REMOVE 4 FRONT PANEL SCREWS TO ACCESS (VRD) SWITCH

LOCATION AND VENTILATION

The welder should be located to provide an unrestrict- ed flow of clean, cool air to the cooling air inlets and to avoid restricting the cooling air outlets. Also, locate the welder so that the engine exhaust fumes are prop- erly vented to an outside area.

STACKING

VANTAGE® 580 machines cannot be stacked.

ANGLE OF OPERATION

Engines are designed to run in the level condition which is where the optimum performance is achieved. The maximum angle of continuous operation is 25 degrees in all directions, 35 degrees Intermittent (less than 10 minutes continuous) in all directions. If the engine is to be operated at an angle, provisions must be made for checking and maintaining the oil level at the normal (FULL) oil capacity in the crankcase.

When operating the welder at an angle, the effective fuel capacity will be slightly less than the amount specified.

LIFTING

The VANTAGE® 580 weighs approximately 1460lbs. (662kg.) with a full tank of fuel 1290lbs. (586kg) less fuel. A lift bail is mounted to the machine and should always be used when lifting the machine.

VANTAGE® 580

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Vantage Safety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a LʼArcElectromagnetic Compatibility EMC Methods of Reducing Emissions Mains Supply Thank You Table of Contents Section D Section ESection F SeriesInstallation Technical Specifications Vantage 580 K2963-1Safety Precautions VRD Voltage Reduction DeviceLocation and Ventilation PRE-OPERATION Engine Service Vehicle MountingTowing OILBattery Connection Remote ControlFuel Engine Cooling SystemElectrical Connections Auxiliary Power Receptacles Standby Power ConnectionsConnection of Lincoln Electric Wire Feeders Connection of LN-15 to the Vantage Shut the welder offAcross The-Arc Model Control Cable ModelInstallation Operation General DescriptionWeld Mode Selector Switch Figure B.1Wire Feeder Voltmeter Switch Table B.1Engine Stop Switch Battery Disconnect SwitchEngine Controls Glow Plug Push ButtonStopping the Engine Welder OperationConstant Current CC-STICK Welding Duty CycleTIG Welding Typical Current Ranges 1 for Tungsten ELECTRODES2Table B.3 Wire WELDING-CV Auxiliary PowerARC Gouging Accessories Field Installed Options / AccessoriesStick Options TIG OptionsWire Feeder Options Maintenance Routine MaintenanceAIR Cleaner Engine OIL ChangeOIL Filter Change Service Instructions Cooling System Tightening the FAN BeltBleeding the Fuel System Engine Adjustment Battery MaintenanceServicing Optional Spark Arrestor Welder / Generator Maintenance Gfci Module Testing and Resetting ProcedureTroubleshooting HOW to USE Troubleshooting GuideAuthorized Field Service Facility LincolnContact your local Lincoln Welding without a control cable Troubleshooting Faulty control cable. Repair or Field Service Facility Your local Lincoln AuthorizedDiagrams Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Wiring Diagram Dimension Print VantagePrecaucion Warnung

IM10064 specifications

The Lincoln Electric IM10064 is a cutting-edge welding machine, designed to meet the diverse needs of both professionals and hobbyists. Renowned for its reliability and performance, the IM10064 stands out by incorporating advanced technologies and features that enhance usability and efficiency.

One of the main features of the IM10064 is its compact and portable design. Weighing significantly less than many other models in its category, it allows for easy transportation to job sites or workshops. Its user-friendly interface includes an easy-to-read digital display, offering precise control over welding parameters, which is crucial for achieving optimal results.

A significant technological advancement in the IM10064 is its inverter technology. This allows the machine to provide a stable and consistent arc, crucial for various welding applications including MIG, TIG, and stick welding. The inverter design not only contributes to its lightweight nature but also increases energy efficiency, reducing operational costs while delivering high performance.

The IM10064 is equipped with a range of power settings, making it suitable for welding different materials and thicknesses. Whether you are working with thin sheets or thicker components, this machine can be adjusted to match the specific requirements of the job. The versatile design ensures that it can be used across various industries and applications, from fabrication and repair to automotive and metal art projects.

Another prominent characteristic is the machine's durable construction. Lincoln Electric has built the IM10064 with high-quality materials that provide resilience against wear and tear in harsh working environments. This durability extends the life of the machine, making it a wise investment for users who demand reliability.

Additionally, the IM10064 features built-in safety mechanisms, such as over-temperature protection and a duty cycle indicator, ensuring that users can operate the machine with confidence. This focus on safety not only protects the operator but also enhances the longevity of the equipment.

In summary, the Lincoln Electric IM10064 is a sophisticated welding solution that combines portability, cutting-edge inverter technology, and durability. Its range of power settings, user-friendly controls, and robust safety features make it an ideal choice for professionals and enthusiasts alike, seeking efficiency and quality in their welding tasks.
Top Page Image Contents