Lincoln Electric IM10064 Stopping the Engine, Welder Operation, Constant Current CC-STICK Welding

Page 23

B-5

OPERATION

B-5

 

 

 

NOTE: If the unit fails to start turn Run/Stop switch to off and repeat step 3 through step 7 after waiting 30 seconds.

CAUTION

•Do not allow the starter motor to run continuously for more than 20 seconds.

•Do not push the START button while the engine is running because this can damage the ring gear and/or the starter motor.

•IF the Engine Protection or Battery Charging Lights do “not” turn off shortly after starting the engine shut off the engine immediately and determine the cause.

-----------------------------------------------------------------------

NOTE: When starting for the first time, or after and extended period of time of not operating, it will take longer than normal to start because the fuel pump has to fill the fuel system. For best results, bleed the fuel system as indicated in Maintenance Section of this manual.

STOPPING THE ENGINE

Remove all welding and auxiliary power loads and allow the engine to run at low idle speed for a few minutes to cool the engine.

STOP the engine by placing the RUN-STOP switch in the STOP position.

NOTE: A fuel shut off valve is located on the fuel pre-filter.

WELDER OPERATION

DUTY CYCLE

Duty Cycle is the percentage of time the load is being applied in a 10 minute period. For example a 60% duty cycle, represents 6 minutes of load and 4 minutes of no load in a 10 minute period.

ELECTRODE INFORMATION

For any electrode the procedures should be kept with- in the rating of the machine. For information on elec- trodes and their proper application see (www.lincoln- electric.com) or the appropriate Lincoln publication.

The VANTAGE® 580 can be used with a broad range of DC stick electrodes. The MODE switch provides two stick welding settings as follows:

CONSTANT CURRENT (CC-STICK) WELDING

The CC-STICK position of the MODE switch is designed for horizontal and vertical-up welding with all types of electrodes, especially low hydrogen.

The ARC CONTROL dial sets the short circuit current (arc-force) during stick welding to adjust for a soft or crisp arc. Increasing the number from -10(soft) to +10(crisp) increases the short circuit current and pre- vents sticking of the electrode to the plate while welding. This can also increase spatter. It is recommended that the ARC CONTROL be set to the minimum number without electrode sticking. Start with the dial set at 0.

NOTE: Due to the low OCV with the VRD on, a very slight delay during striking of the electrodes may occur. Due to the requirement of the resis- tance in the circuit to be low for a VRD to operate, a good metal-to-metal contact must be made between the metal core of the electrode and the job. A poor connection anywhere in the welding output circuit may limit the operation of the VRD. This includes a good connection of the work clamp to the job. The work clamp should be connected as close as practical to where the welding will be per- formed.

A. For New Electrodes

E6010 - Touch, Lift to Start the Arc

E7018, E7024 - Touch, Rock Back and Forth in Joint, Lift .

Once the arc is started, normal welding technique for the application is then used.

B. For Re-Striking Electrodes

Some electrodes form a cone at the end of the electrode after the welding arc has been broken, particularly iron powder and low hydrogen elec- trodes. This cone will need to be broken off in order to have the metal core of the electrode make con- tact.

E6010 - Push, Twist in Joint, Lift

E7018, E7024 - Push, Rock Back and Forth in

Joint, Lift.

Once the arc is started, normal welding technique for the application is then used.

For other electrodes the above techniques should be tried first and varied as needed to suit operator preference. The goal for successful starting is good metal to metal contact.

For indicator light operation, see Table B.1.

DOWNHILL PIPE Welding

This slope controlled setting is intended for "out-of- position" and "down hill" pipe welding where the oper- ator would like to control the current level by changing the arc length.

VANTAGE® 580

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Vantage California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionSûreté Pour Soudage a LʼArc Précautions DE SûretéElectromagnetic Compatibility EMC Methods of Reducing Emissions Mains Supply Thank You Table of Contents Series Section DSection E Section FTechnical Specifications Vantage 580 K2963-1 InstallationLocation and Ventilation Safety PrecautionsVRD Voltage Reduction Device OIL PRE-OPERATION Engine ServiceVehicle Mounting TowingEngine Cooling System Battery ConnectionRemote Control FuelElectrical Connections Standby Power Connections Auxiliary Power ReceptaclesControl Cable Model Connection of Lincoln Electric Wire FeedersConnection of LN-15 to the Vantage Shut the welder off Across The-Arc ModelInstallation General Description OperationFigure B.1 Weld Mode Selector SwitchTable B.1 Wire Feeder Voltmeter SwitchGlow Plug Push Button Engine Stop SwitchBattery Disconnect Switch Engine ControlsDuty Cycle Stopping the EngineWelder Operation Constant Current CC-STICK WeldingTable B.3 TIG WeldingTypical Current Ranges 1 for Tungsten ELECTRODES2 ARC Gouging Wire WELDING-CVAuxiliary Power TIG Options AccessoriesField Installed Options / Accessories Stick OptionsWire Feeder Options Routine Maintenance MaintenanceOIL Filter Change AIR CleanerEngine OIL Change Service Instructions Bleeding the Fuel System Cooling SystemTightening the FAN Belt Servicing Optional Spark Arrestor Engine AdjustmentBattery Maintenance Gfci Module Testing and Resetting Procedure Welder / Generator MaintenanceHOW to USE Troubleshooting Guide TroubleshootingContact your local Lincoln Authorized Field Service FacilityLincoln Welding without a control cable Troubleshooting Faulty control cable. Repair or Your local Lincoln Authorized Field Service FacilityDiagrams Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams Wiring Diagram Vantage Dimension PrintPrecaucion Warnung

IM10064 specifications

The Lincoln Electric IM10064 is a cutting-edge welding machine, designed to meet the diverse needs of both professionals and hobbyists. Renowned for its reliability and performance, the IM10064 stands out by incorporating advanced technologies and features that enhance usability and efficiency.

One of the main features of the IM10064 is its compact and portable design. Weighing significantly less than many other models in its category, it allows for easy transportation to job sites or workshops. Its user-friendly interface includes an easy-to-read digital display, offering precise control over welding parameters, which is crucial for achieving optimal results.

A significant technological advancement in the IM10064 is its inverter technology. This allows the machine to provide a stable and consistent arc, crucial for various welding applications including MIG, TIG, and stick welding. The inverter design not only contributes to its lightweight nature but also increases energy efficiency, reducing operational costs while delivering high performance.

The IM10064 is equipped with a range of power settings, making it suitable for welding different materials and thicknesses. Whether you are working with thin sheets or thicker components, this machine can be adjusted to match the specific requirements of the job. The versatile design ensures that it can be used across various industries and applications, from fabrication and repair to automotive and metal art projects.

Another prominent characteristic is the machine's durable construction. Lincoln Electric has built the IM10064 with high-quality materials that provide resilience against wear and tear in harsh working environments. This durability extends the life of the machine, making it a wise investment for users who demand reliability.

Additionally, the IM10064 features built-in safety mechanisms, such as over-temperature protection and a duty cycle indicator, ensuring that users can operate the machine with confidence. This focus on safety not only protects the operator but also enhances the longevity of the equipment.

In summary, the Lincoln Electric IM10064 is a sophisticated welding solution that combines portability, cutting-edge inverter technology, and durability. Its range of power settings, user-friendly controls, and robust safety features make it an ideal choice for professionals and enthusiasts alike, seeking efficiency and quality in their welding tasks.
Top Page Image Contents