| TROUBLESHOOTING |
|
|
|
| |||||||||
|
|
| Observe all Safety Guidelines detailed throughout this manual |
|
| |||||||||
|
| PROBLEMS |
|
|
|
| POSSIBLE |
|
|
| RECOMMENDED |
|
| |
|
|
|
|
|
|
| ||||||||
|
| (SYMPTOMS) |
|
|
|
| CAUSE |
|
|
| COURSE OF ACTION |
|
| |
|
|
|
|
|
|
|
| OUTPUT PROBLEMS |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| Poor arc striking with electrode |
|
|
| 1. Make sure settings for wire feed |
|
|
|
|
|
| ||
|
| sticking or blasting off. |
|
|
|
| speed and voltage are correct |
|
|
|
|
|
| |
|
|
|
|
|
|
| 2. | for process being used. |
|
|
|
|
|
|
|
|
|
|
|
|
| The gas shielding may be |
|
|
|
|
|
| |
|
|
|
|
|
|
| 3. | improper for process being used. |
|
|
|
|
|
|
|
|
|
|
|
|
| Check input line voltage to be |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| with in machines recommended |
|
|
|
|
|
|
|
|
|
|
|
|
| 4. | rating range. |
|
|
|
|
|
|
|
|
|
|
|
|
| Check that the machine recon- |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| nect panel is configured properly |
|
|
|
|
|
|
|
|
|
|
|
|
|
| for the applied voltage. |
|
|
|
|
|
|
|
| Auxiliary receptacle is “dead” - no |
|
|
| 1. Circuit breaker (on case back) |
|
|
|
|
|
| ||
|
| auxiliary voltage. |
|
|
|
|
| may have opened. Reset. |
|
|
|
|
|
|
|
| Rough wire feeding or wire will not |
|
|
|
| FEEDING PROBLEMS |
|
|
| If all recommended possible areas |
| ||
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
| 1. The gun cable may be kinked or twisted. |
|
|
|
| |||||
|
| feed but drive rolls are turning. |
|
|
| 2. The wire may be jammed in the gun |
|
|
| of misadjustment have been |
|
| ||
|
|
|
|
|
|
| 3. | cable, or gun cable may be dirty. |
|
|
| checked and the problem persists, |
| |
|
|
|
|
|
|
| Check drive roll tension and |
|
|
| Contact your local Lincoln |
|
| |
|
|
|
|
|
|
| 4. | position of grooves. |
|
|
| Authorized Field Service Facility. |
| |
|
|
|
|
|
|
| Check for worn or loose drive rolls. |
|
|
|
|
|
| |
|
|
|
|
|
|
| 5. | The electrode may be rusty or dirty. |
|
|
|
|
|
|
|
|
|
|
|
|
| 6. | Check for damaged or incorrect |
|
|
|
|
|
|
|
|
|
|
|
|
| 7. | contact tip. |
|
|
|
|
|
|
|
|
|
|
|
|
| Check wire spindle for ease of |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| rotation and adjust break ten- |
|
|
|
|
|
|
|
|
|
|
|
|
| 8. | sion knob if necessary. |
|
|
|
|
|
|
|
|
|
|
|
|
| Check that the gun is pushed all |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| the way into gun mount and |
|
|
|
|
|
|
|
|
|
|
|
|
|
| properly seated. |
|
|
|
|
|
|
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your LOCAL AUTHORIZED LINCOLN ELECTRIC FIELD SERVICE FACILITY for assistance before you proceed.
POWER MIG 215