Friedrich WE10B33A-B, WS08B10A-C, WE16B33A-B manual Normal Function of Valve, Malfunction of Valve

Page 14

TROUBLESHOOTING TOUCH TEST CHART: TO SERVICE REVERSING VALVES

NORMAL FUNCTION OF VALVE

VALVE

DISCHARGETUBE fromCompressor

SUCTIONTUBEto Compressor

Tube toINSIDE COIL

TubeOUTSIDEto COIL

LEFT Pilot CapillaryTube

RIGHT Pilot

CapillaryTube

NOTES:

 

OPERATING

* TEMPERATURE OF VALVE BODY

CONDITION

** WARMER THAN VALVE BODY

 

 

 

 

1

2

3

 

4

5

6

POSSIBLE CAUSES

CORRECTIONS

Normal Cooling

Hot

Cool

Cool

Hot

*TVB

TVB

 

 

as (2)

as (1)

 

 

 

 

 

 

 

 

 

Normal Heating

Hot

Cool

Hot

Cool

*TVB

TVB

 

 

as (1)

as (2)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MALFUNCTION OF VALVE

 

 

Check Electrical circuit and coil

 

 

 

No voltage to coil.

Repair electrical circuit.

 

 

 

 

Defective coil.

Replace coil.

 

 

 

 

 

 

 

 

 

Check refrigeration charge

 

 

 

Low charge.

Repair leak, recharge system.

 

 

 

 

Pressure differential too high.

Recheck system.

 

 

 

 

 

 

 

 

Valve will not

Hot

Cool

Cool,

 

Hot,

*TVB

Hot

 

Deenergize solenoid, raise head pressure,

 

 

as (2)

 

as (1)

 

 

 

reenergize solenoid to break dirt loose.

shift from cool

 

 

 

 

 

 

 

Pilot valve okay. Dirt in one bleeder hole.

If unsuccessful, remove valve, wash

to heat.

 

 

 

 

 

 

 

 

out. Check on air before installing. If no

 

 

 

 

 

 

 

 

 

movement, replace valve, add strainer to

 

 

 

 

 

 

 

 

 

discharge tube, mount valve horizontally.

 

 

 

 

 

 

 

 

 

Stop unit. After pressures equalize, restart

 

 

 

 

 

 

 

 

Piston cup leak

with solenoid energized. If valve shifts,

 

 

 

 

 

 

 

 

reattempt with compressor running. If still

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

no shift, replace valve.

 

Hot

Cool

Cool,

 

Hot,

*TVB

*TVB

Clogged pilot tubes.

Raise head pressure, operate solenoid to

 

as (2)

 

as (1)

free. If still no shift, replace valve.

Valve will not

 

 

 

 

 

 

 

 

Cool,

 

Hot,

 

 

Both ports of pilot open. (Back seat port

Raise head pressure, operate solenoid to free

shift from cool

Hot

Cool

 

Hot

Hot

partially clogged port. If still no shift, replace

as (2)

 

as (1)

did not close).

to heat.

 

 

 

 

 

 

 

 

valve.

 

Warm

Cool

Cool,

 

Hot,

*TVB

Warm

Defective Compressor.

Replace compressor

 

as (2)

 

as (1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Not enough pressure differential at start

Check unit for correct operating pressures

 

Hot

Warm

Warm

 

Hot

*TVB

Hot

of stroke or not enough flow to maintain

and charge. Raise head pressure. If no

 

 

 

 

 

 

 

 

pressure differential.

shift, use valve with smaller port.

 

 

 

 

 

 

 

 

 

 

Starts to shift

 

 

 

 

 

 

 

Body damage.

Replace valve

Hot

Warm

Warm

 

Hot

Hot

Hot

Both ports of pilot open.

Raise head pressure, operate solenoid. If

but does not

 

no shift, use valve with smaller ports.

 

 

 

 

 

 

 

 

complete

Hot

Hot

Hot

 

Hot

*TVB

Hot

Body damage.

Replace valve

reversal.

 

 

 

 

 

 

 

Valve hung up at mid-stroke. Pumping

Raise head pressure, operate solenoid. If

 

 

 

 

 

 

 

 

volume of compressor not sufficient to

no shift, use valve with smaller ports.

 

 

 

 

 

 

 

 

maintain reversal.

 

 

 

 

 

 

 

 

 

 

Hot

Hot

Hot

 

Hot

Hot

Hot

Both ports of pilot open.

Raise head pressure, operate solenoid. If no

 

 

shift, replace valve.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Apparent

Hot

Cool

Hot,

 

Cool,

*TVB

*TVB

Piston needle on end of slide leaking.

Operate valve several times, then recheck.

as (1)

 

as (2)

If excessive leak, replace valve.

 

 

 

 

 

 

leap in heating.

 

 

 

 

 

 

 

 

 

Hot

Cool

Hot,

 

Cool,

** WVB

** WVB

Pilot needle and piston needle leaking.

Operate valve several times, then recheck.

 

as (1)

 

as (2)

If excessive leak, replace valve.

 

 

 

 

 

 

 

 

Hot

Cool

Hot,

 

Cool,

*TVB

*TVB

Pressure differential too high.

Stop unit. Will reverse during equalization

 

as (1)

 

as (2)

period. Recheck system

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Clogged pilot tube.

Raise head pressure, operate solenoid to

 

 

 

 

 

 

 

 

free dirt. If still no shift, replace valve.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Raise head pressure, operate solenoid.

 

 

 

Hot,

 

Cool,

 

 

 

Remove valve and wash out. Check on air

 

Hot

Cool

 

Hot

*TVB

Dirt in bleeder hole.

before reinstalling, if no movement, replace

Will not shift

as (1)

 

as (2)

 

 

 

 

 

 

valve. Add strainer to discharge tube.

 

 

 

 

 

 

 

 

from heat to

 

 

 

 

 

 

 

 

Mount valve horizontally.

 

 

 

 

 

 

 

 

Stop unit. After pressures equalize, restart

cool.

 

 

 

 

 

 

 

 

 

 

Hot,

 

Cool,

 

 

 

with solenoid deenergized. If valve shifts,

 

Hot

Cool

 

Hot

*TVB

Piston cup leak.

reattempt with compressor running. If it

 

as (1)

 

as (2)

 

 

 

 

 

 

 

still will not reverse while running, replace

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the valve.

 

Hot

Cool

Hot,

 

Cool,

Hot

Hot

Defective pilot.

Replace valve.

 

as (1)

 

as (2)

 

 

 

 

 

 

 

 

 

Warm

Cool

Warm,

 

Cool,

Warm

*TVB

Defective compressor.

Replace compressor

 

as (1)

 

as (2)

 

 

 

 

 

 

 

 

14

Image 14
Contents Service & Parts Manual Table of Contents WALLMASTER≤ THRU-THE-WALL AIR Conditioners Limited Warranty Routine Maintenance Friedrich Room Model Number Code RAC Serial Number Identification GuidePerformance Data OperatingElectrical Data Electric Shock HazardFunctional Components Mechanical componentsActivating Test Mode Testing the Electronic ControlChecking Room Temperature Error Code ListingsSystem Control Switch System Control Switch TestRefrigeration System Sequence of Operation Sealed Refrigeration System RepairsEquipment Required Hermetic Component ReplacementSealed Refrigeration System Repairs Equipment Must be CapableRefrigerant Charge Special Procedure in the Case of Motor Compressor BurnoutRotary Compressor Special Troubleshooting and Service Normal Function of Valve Malfunction of ValveCooling only Room AIR Conditioners Troubleshooting Tips Problem Possible Cause ActionReplace fuse, reset breaker. If repeats, check Problem Possible Cause Action Water spitting Heat / Cool Room AIR Conditioners Troubleshooting Tips Problem Possible Cause Action Wiring Diagram Models WS08B10A-C, WS10B10A-C Wiring Diagram Models WS16B30A-C Wiring Diagram Models WE10B33A-B, WE13B33B-B Wiring Diagram Models WE16B33A-B Wiring Diagram Models WY10B33A-B, WY13B33A-B WS, WE & WY Series Chassis Parts 46AWallmaster Parts Electrical PartsSHROUD, Condenser WS WE WY Series Sleeve Parts WS, WE & WY Series Sleeve PartsWM-Svc-Prts-07

WS10B10A-C, WS10B30A-C, WS16B30A-C, WS13B30B-C, WY10B33A-B specifications

Friedrich manufactures a range of high-quality air conditioning units, including models WY13B33A-B, WS13B30B-C, WE16B33A-B, WS10B10A-C, and WS08B10A-C. These units are designed to offer reliable climate control for both residential and commercial spaces, while incorporating advanced technologies and energy-efficient features.

The WY13B33A-B model stands out with its impressive cooling capacity of 13,000 BTU, making it ideal for medium-sized rooms. It employs inverter technology, which not only optimizes energy consumption but also ensures a quieter operation by adjusting the compressor speed based on cooling demand. This model is equipped with a programmable thermostat, allowing users to set preferred temperatures and schedules, enhancing both comfort and efficiency.

The WS13B30B-C also features a robust cooling capability, paired with a sleek design that fits seamlessly into various interiors. Its user-friendly digital control panel and remote control operation enhance the overall user experience. Additionally, the unit is designed with energy-saving modes that further contribute to lower electricity bills without sacrificing performance.

The WE16B33A-B model is tailored for larger spaces, boasting a cooling capacity of 16,000 BTU. This makes it a great choice for open-plan areas or rooms with high ceilings. Its multi-speed fan and adjustable louvers provide customized airflow, ensuring that every corner of the room is adequately cooled. Notably, this model includes a dehumidification function that efficiently reduces humidity levels, promoting a more comfortable environment.

On the other hand, the WS10B10A-C and WS08B10A-C models are compact, making them perfect for smaller areas or specific applications such as bedrooms or home offices. Both units have a cooling capacity of 10,000 BTU and 8,000 BTU, respectively. They feature easy-to-use mechanical controls and are designed for simple installation, making them an excellent choice for individuals seeking an affordable yet effective cooling solution.

All Friedrich air conditioning units are built with durability and longevity in mind, incorporating high-quality materials and construction practices. Additionally, they boast reliable warranty options, ensuring peace of mind for consumers. In summary, Friedrich’s WY13B33A-B, WS13B30B-C, WE16B33A-B, WS10B10A-C, and WS08B10A-C models represent a blend of innovative technology, energy efficiency, and performance, tailored to meet diverse cooling needs.