Lincoln Electric IM10056 manual Wire Drive Configuration, Changing the GUN Receiver bUSHING

Page 13

A-4

INSTALLATION

A-4

 

 

 

WIRE DRIVE CONFIGURATION

(See Figure A.2)

CHANGING THE GUN RECEIVER bUSHING

WARNING

ELECTRIC SHOCK can kill.

•Turn the input power OFF at the welding power source before instal- lation or changing drive rolls and/or guides.

•Do not touch electrically live parts.

•When inching with the gun trigger, electrode and drive mechanism are "hot" to work and ground and could remain energized several sec- onds after the gun trigger is released.

•Do not operate with covers, panels or guards removed or open.

•Only qualified personnel should perform mainte- nance work.

------------------------------------------------------------------------

Tools required:

• 1/4" hex key wrench.

Note: Some gun bushings do not require the use of the thumb screw.

1.Turn power off at the welding power source.

2.Remove the welding wire from the wire drive.

3.Remove the thumb screw from the wire drive.

4.Remove the welding gun from the wire drive.

5.Loosen the socket head cap screw that holds the connector bar against the gun bushing.

Important: Do not attempt to completely remove the socket head cap screw.

6.Remove the outer wire guide, and push the gun bushing out of the wire drive. Because of the pre- cision fit, light tapping may be required to remove the gun bushing.

7.Disconnect the shielding gas hose from the gun bushing, if required.

FIGURE A.2

8.Connect the shielding gas hose to the new gun bushing, if required.

9.Rotate the gun bushing until the thumb screw hole aligns with the thumb screw hole in the feed plate. Slide the gun receiver bushing into the wire drive and verify the thumb screw holes are aligned.

10.Tighten the socket head cap screw.

11.Insert the welding gun into the gun bushing and tighten the thumb screw.

PROCEDURE TO INSTALL DRIVE ROLLS AND WIRE GUIDES

WARNING

•Turn the input power OFF at the welding power source before instal- lation or changing drive rolls and/or guides.

•Do not touch electrically live parts.

•When inching with the gun trigger, electrode and drive mechanism are "hot" to work and ground and could remain energized several sec- onds after the gun trigger is released.

•Do not operate with covers, panels or guards removed or open.

•Only qualified personnel should perform mainte- nance work.

------------------------------------------------------------------------

1.Turn power off at the welding power source.

2.Release the idle roll pressure arm.

3.Remove the outer wire guide by turning the knurled thumbscrews counter-clockwise to unscrew them from the feed plate.

4.Rotate the triangular lock and remove the drive rolls.

THUMB SCREW

GUN RECEIVER BUSHING

OUTER WIRE GUIDE

CONNECTOR BLOCK

SOCKET HEAD

CAP SCREW

LOOSEN TIGHTEN

5.Remove the inner wire guide.

6.Insert the new inner wire guide, groove side out, over the two locating pins in the feed plate.

7.Install a drive roll on each hub assembly secure with the triangular lock.

8.Install the outer wire guide by aligning it with the pins and tightening the knurled thumbscrews.

9.Close the idle arm and engage the idle roll pressure arm. Adjust the pressure appropriately.

LN™-25 PIPE

Page 12 Page 14
Image 13
Page 12 Page 14
Contents LN- 25 Pipe Safety Depends on YouCalifornia Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionSûreté Pour Soudage a L’Arc Précautions DE SûretéSafety Methods of Reducing Emissions Mains Supply Please Examine Carton and Equipment For Damage Immediately ViiOn-Line Product Registration TAbLE of Contents Technical Specifications LN-25 Pipe K2614-5 InstallationLocation Safety PrecautionsHigh Frequency Protection Weld CAbLE SIzECAbLE Connections Function Pin WiringShielding GAS Connection Procedure to Install Drive Rolls and Wire Guides Wire Drive ConfigurationChanging the GUN Receiver bUSHING Loading Spools of Wire Pressure ARM AdjustmentGUN Connection Fe, CrNiDescription Power Source to LN-25 PipeFigure A.8 Operation Safety PrecautionsGeneral Description Case Front Controls See Figure b.1 Wire Feed Speed KNObDescription Wire Feed SPEED/AMPERAGE Display POWER-UP SequenceThermal LED, Motor Overload Model Run-in Wire Feed Speed Wire Feed Speed UnitsWFS CALIbRATION with Digital Meters Inches/minute forWFS KNOb Range Left Display SelectionItemdescription Internal ControlsInternal Controls Description Step Trigger Interlock SwitchCold Feed PUSHbUTTON Step TriggerGAS Purge PUSHbUTTON Rear ControlsFactory Installed Equipment AccessoriesDrive Roll Kits See Parts Pages Accessories K1500-5 Gun Receiver Bushing compatible Routine Maintenance MaintenancePeriodic Maintenance Electric Shock can kill TROUbLESHOOTINGSymptoms PRObLEMSPOSSIbLE Cause Recommended Course of ActionOutput Problems TROUbLESHOOTING LN-25 Pipe Diagrams17.19 Dimension PrintLN-25 Pipe Precaucion Warnung

IM10056 specifications

The Lincoln Electric IM10056 is a versatile and powerful electric welder designed for professionals and DIY enthusiasts alike. Known for its robust construction and user-friendly features, the IM10056 stands out in the welding equipment market. This welder is ideal for a variety of applications, including fabrication, repair, and maintenance tasks, making it a popular choice for both commercial and home workshops.

One of the key features of the Lincoln Electric IM10056 is its impressive power output. The machine is equipped with a high-performance inverter technology that provides a stable arc, allowing for smooth and consistent welds even on thin materials. This inverter technology also contributes to energy efficiency, reducing operational costs while maintaining high performance standards.

The IM10056 offers a wide range of welding capabilities, supporting different processes such as MIG, TIG, and stick welding. This multi-process functionality allows users to switch between welding techniques easily, making it an incredibly adaptable machine for various projects. The intuitive controls and digital display simplify the setup process, enabling welders to quickly adjust settings for optimal performance.

Another notable characteristic of the Lincoln Electric IM10056 is its portability. Weighing in at a manageable level, this welder can be easily transported to job sites or stored away when not in use. Its compact design does not compromise functionality; it still delivers robust performance in tight spaces.

Safety features are also a primary consideration in the design of the IM10056. The welder includes an integrated cooling system to prevent overheating, which enhances durability and extends the machine’s lifespan. Additionally, it comes with protection against overload, ensuring that users can operate the device confidently without the risk of damage.

Moreover, maintenance is made easy with the Lincoln Electric IM10056. Regular service requirements are minimized due to its reliable construction and technological advancements, making it an ideal choice for users who want a durable and long-lasting tool.

In summary, the Lincoln Electric IM10056 is a well-rounded, feature-rich welding machine that combines power, efficiency, and versatility. With its advanced technologies, multi-process capabilities, user-friendly interface, and safety features, it is a leading choice for anyone looking to tackle their welding projects with precision and confidence. Whether for professional or personal use, the IM10056 delivers exceptional performance that meets the demands of modern welding applications.
Top Page Image Contents