Lincoln Electric IM10056 manual Safety

Page 6

v

SAFETY

v

Electromagnetic Compatibility (EMC)

Conformance

Products displaying the CE mark are in conformity with European Community Council Directive of 15 Dec 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility, 2004/108/EC. It was manufactured in conformity with a national standard that implements a harmonized standard: EN 60974-10 Electromagnetic Compatibility (EMC) Product Standard for Arc Welding Equipment. It is for use with other Lincoln Electric equipment. It is designed for industrial and professional use.

Introduction

All electrical equipment generates small amounts of electromagnetic emission. Electrical emission may be transmitted through power lines or radiated through space, similar to a radio transmitter. When emissions are received by other equipment, electrical interference may result. Electrical emissions may affect many kinds of electrical equipment; other nearby welding equipment, radio and TV reception, numerical controlled machines, telephone systems, computers, etc. Be aware that interference may result and extra precautions may be required when a welding power source is used in a domestic establishment.

Installation and Use

The user is responsible for installing and using the welding equipment according to the manufacturer’s instructions. If electromagnetic disturbances are detected then it shall be the responsibility of the user of the welding equipment to resolve the situation with the technical assistance of the manufacturer. In some cases this remedial action may be as simple as earthing (grounding) the welding circuit, see Note. In other cases it could involve construction of an electromagnetic screen enclosing the power source and the work complete with associated input filters. In all cases electromagnetic disturbances must be reduced to the point where they are no longer troublesome.

Note: The welding circuit may or may not be earthed for safety reasons according to national codes. Changing the earthing arrangements should only be authorized by a person who is compe- tent to access whether the changes will increase the risk of injury, e.g., by allowing parallel welding current return paths which may damage the earth circuits of other equipment.

Assessment of Area

Before installing welding equipment the user shall make an assessment of potential electromagnetic prob- lems in the surrounding area. The following shall be taken into account:

a)other supply cables, control cables, signaling and telephone cables; above, below and adjacent to the welding equipment;

b)radio and television transmitters and receivers;

c)computer and other control equipment;

d)safety critical equipment, e.g., guarding of industrial equipment;

e)the health of the people around, e.g., the use of pacemakers and hearing aids;

f)equipment used for calibration or measurement

g)the immunity of other equipment in the environment. The user shall ensure that other equipment being used in the environment is compatible. This may require additional protection measures;

h)the time of day that welding or other activities are to be carried out.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Safety Depends on You LN- 25 PipeSafety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcSafety Methods of Reducing Emissions Mains Supply Vii Please Examine Carton and Equipment For Damage ImmediatelyOn-Line Product Registration TAbLE of Contents Installation Technical Specifications LN-25 Pipe K2614-5High Frequency Protection Safety PrecautionsLocation Weld CAbLE SIzEFunction Pin Wiring CAbLE ConnectionsShielding GAS Connection Wire Drive Configuration Procedure to Install Drive Rolls and Wire GuidesChanging the GUN Receiver bUSHING GUN Connection Pressure ARM AdjustmentLoading Spools of Wire Fe, CrNiPower Source to LN-25 Pipe DescriptionFigure A.8 Safety Precautions OperationGeneral Description Wire Feed Speed KNOb Case Front Controls See Figure b.1Description POWER-UP Sequence Wire Feed SPEED/AMPERAGE DisplayThermal LED, Motor Overload WFS CALIbRATION with Digital Meters Wire Feed Speed UnitsModel Run-in Wire Feed Speed Inches/minute forLeft Display Selection WFS KNOb RangeInternal Controls ItemdescriptionCold Feed PUSHbUTTON Step Trigger Interlock SwitchInternal Controls Description Step TriggerRear Controls GAS Purge PUSHbUTTONAccessories Factory Installed EquipmentDrive Roll Kits See Parts Pages Accessories K1500-5 Gun Receiver Bushing compatible Maintenance Routine MaintenancePeriodic Maintenance TROUbLESHOOTING Electric Shock can killPOSSIbLE PRObLEMSSymptoms Cause Recommended Course of ActionOutput Problems TROUbLESHOOTING Diagrams LN-25 PipeDimension Print 17.19LN-25 Pipe Precaucion Warnung

IM10056 specifications

The Lincoln Electric IM10056 is a versatile and powerful electric welder designed for professionals and DIY enthusiasts alike. Known for its robust construction and user-friendly features, the IM10056 stands out in the welding equipment market. This welder is ideal for a variety of applications, including fabrication, repair, and maintenance tasks, making it a popular choice for both commercial and home workshops.

One of the key features of the Lincoln Electric IM10056 is its impressive power output. The machine is equipped with a high-performance inverter technology that provides a stable arc, allowing for smooth and consistent welds even on thin materials. This inverter technology also contributes to energy efficiency, reducing operational costs while maintaining high performance standards.

The IM10056 offers a wide range of welding capabilities, supporting different processes such as MIG, TIG, and stick welding. This multi-process functionality allows users to switch between welding techniques easily, making it an incredibly adaptable machine for various projects. The intuitive controls and digital display simplify the setup process, enabling welders to quickly adjust settings for optimal performance.

Another notable characteristic of the Lincoln Electric IM10056 is its portability. Weighing in at a manageable level, this welder can be easily transported to job sites or stored away when not in use. Its compact design does not compromise functionality; it still delivers robust performance in tight spaces.

Safety features are also a primary consideration in the design of the IM10056. The welder includes an integrated cooling system to prevent overheating, which enhances durability and extends the machine’s lifespan. Additionally, it comes with protection against overload, ensuring that users can operate the device confidently without the risk of damage.

Moreover, maintenance is made easy with the Lincoln Electric IM10056. Regular service requirements are minimized due to its reliable construction and technological advancements, making it an ideal choice for users who want a durable and long-lasting tool.

In summary, the Lincoln Electric IM10056 is a well-rounded, feature-rich welding machine that combines power, efficiency, and versatility. With its advanced technologies, multi-process capabilities, user-friendly interface, and safety features, it is a leading choice for anyone looking to tackle their welding projects with precision and confidence. Whether for professional or personal use, the IM10056 delivers exceptional performance that meets the demands of modern welding applications.
Top Page Image Contents