Lincoln Electric IM10056 manual Pressure ARM Adjustment, Loading Spools of Wire, GUN Connection

Page 14

A-5

INSTALLATION

A-5

 

 

 

PRESSURE ARM ADJUSTMENT

1.Squeeze the release bar on the retaining collar and remove it from the spindle.

WARNING

ELECTRIC SHOCK can kill.

•Turn the input power OFF at the weld- ing power source before installation or changing drive rolls and/or guides.

•Do not touch electrically live parts.

•When inching with the gun trigger, electrode and drive mechanism are "hot" to work and ground and could remain energized several sec- onds after the gun trigger is released.

•Do not operate with covers, panels or guards removed or open.

•Only qualified personnel should perform mainte- nance work.

------------------------------------------------------------------------

The pressure arm controls the amount of force the drive rolls exert on the wire. Proper adjustment of the pressure arm gives the best welding performance.

Set the pressure arm as follows:

 

(See Figure A.3)

 

Aluminum wires

between 1 and 2

Cored wires

between 2 and 3

Steel, Stainless wires

between 3 and 5

FIGURE A.3

 

Al

 

 

 

ALUMINUM WIRES

 

 

 

 

 

Fe, CrNi

 

 

 

 

CORED WIRES

 

 

 

 

6

Fe, CrNi

 

 

 

STEEL, STAINLESS WIRES

 

 

 

LOADING SPOOLS OF WIRE

WARNING

•Keep hands, hair, clothing and tools away from rotating equipment.

•Do not wear gloves when threading wire or changing wire spool.

•Only qualified personnel should install, use or service this equipment.

------------------------------------------------------------------------

Loading 10 to 15 lb. (4.5 – 6.8kg) Spools.

A K468 spindle adapter is required for loading 2" (51mm) wide spools on 2" (51mm) spindles. Use a K468 spindle adapter for loading 2-1/2" (64mm) wide spools.

2.Place the spindle adapter on the spindle, aligning the spindle brake pin with the hole in the adapter.

3.Place the spool on the spindle and align the adapter brake tab with one of the holes in the back side of the spool. An indicator mark on the end of the spindle shows the orientation of the brake tab. Be certain the wire feeds off of the spool in the proper direction.

4.Re-install the retaining collar. Make sure that the release bar snaps out and that the retaining collar fully engages the groove on the spindle.

GUN CONNECTION

WARNING

ELECTRIC SHOCK can kill.

•Turn the input power OFF at the weld- ing power source before installation or changing drive rolls and/or guides.

•Do not touch electrically live parts.

•When inching with the gun trigger, electrode and drive mechanism are "hot" to work and ground and could remain energized several sec- onds after the gun trigger is released.

•Do not operate with covers, panels or guards removed or open.

•Only qualified personnel should perform mainte- nance work.

------------------------------------------------------------------------

The LN™-25 PIPE comes with a K1500-2 gun adapter installed. (See Figure A.4)

To install a gun,

1.Turn power OFF.

2.Remove the thumb screw.

3.Push the gun the completely into the gun bushing.

4.Secure the gun in place with the thumb screw.

5.Connect the trigger cable from the gun to the trigger connector on the front of the feeder.

Note: Not all gun bushings require the use of the thumb screw.

FIGURE A.4

THUMB

SCREW

GUN

LN™-25 PIPE

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Safety Depends on You LN- 25 PipeSafety California Proposition 65 WarningsElectric Shock can kill Welding and Cutting Sparks can Cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcSafety Methods of Reducing Emissions Mains Supply On-Line Product Registration ViiPlease Examine Carton and Equipment For Damage Immediately TAbLE of Contents Installation Technical Specifications LN-25 Pipe K2614-5High Frequency Protection Safety PrecautionsLocation Weld CAbLE SIzEShielding GAS Connection Function Pin WiringCAbLE Connections Changing the GUN Receiver bUSHING Wire Drive ConfigurationProcedure to Install Drive Rolls and Wire Guides GUN Connection Pressure ARM AdjustmentLoading Spools of Wire Fe, CrNiPower Source to LN-25 Pipe DescriptionFigure A.8 Safety Precautions OperationGeneral Description Description Wire Feed Speed KNObCase Front Controls See Figure b.1 Thermal LED, Motor Overload POWER-UP SequenceWire Feed SPEED/AMPERAGE Display WFS CALIbRATION with Digital Meters Wire Feed Speed UnitsModel Run-in Wire Feed Speed Inches/minute forLeft Display Selection WFS KNOb RangeInternal Controls ItemdescriptionCold Feed PUSHbUTTON Step Trigger Interlock SwitchInternal Controls Description Step TriggerRear Controls GAS Purge PUSHbUTTONDrive Roll Kits See Parts Pages AccessoriesFactory Installed Equipment Accessories K1500-5 Gun Receiver Bushing compatible Periodic Maintenance MaintenanceRoutine Maintenance TROUbLESHOOTING Electric Shock can killPOSSIbLE PRObLEMSSymptoms Cause Recommended Course of ActionOutput Problems TROUbLESHOOTING Diagrams LN-25 PipeDimension Print 17.19LN-25 Pipe Precaucion Warnung

IM10056 specifications

The Lincoln Electric IM10056 is a versatile and powerful electric welder designed for professionals and DIY enthusiasts alike. Known for its robust construction and user-friendly features, the IM10056 stands out in the welding equipment market. This welder is ideal for a variety of applications, including fabrication, repair, and maintenance tasks, making it a popular choice for both commercial and home workshops.

One of the key features of the Lincoln Electric IM10056 is its impressive power output. The machine is equipped with a high-performance inverter technology that provides a stable arc, allowing for smooth and consistent welds even on thin materials. This inverter technology also contributes to energy efficiency, reducing operational costs while maintaining high performance standards.

The IM10056 offers a wide range of welding capabilities, supporting different processes such as MIG, TIG, and stick welding. This multi-process functionality allows users to switch between welding techniques easily, making it an incredibly adaptable machine for various projects. The intuitive controls and digital display simplify the setup process, enabling welders to quickly adjust settings for optimal performance.

Another notable characteristic of the Lincoln Electric IM10056 is its portability. Weighing in at a manageable level, this welder can be easily transported to job sites or stored away when not in use. Its compact design does not compromise functionality; it still delivers robust performance in tight spaces.

Safety features are also a primary consideration in the design of the IM10056. The welder includes an integrated cooling system to prevent overheating, which enhances durability and extends the machine’s lifespan. Additionally, it comes with protection against overload, ensuring that users can operate the device confidently without the risk of damage.

Moreover, maintenance is made easy with the Lincoln Electric IM10056. Regular service requirements are minimized due to its reliable construction and technological advancements, making it an ideal choice for users who want a durable and long-lasting tool.

In summary, the Lincoln Electric IM10056 is a well-rounded, feature-rich welding machine that combines power, efficiency, and versatility. With its advanced technologies, multi-process capabilities, user-friendly interface, and safety features, it is a leading choice for anyone looking to tackle their welding projects with precision and confidence. Whether for professional or personal use, the IM10056 delivers exceptional performance that meets the demands of modern welding applications.
Top Page Image Contents