Milwaukee 626, 6276 manual Tool Assembly, Adjusting the shoe Fig

Page 5

TOOL ASSEMBLY

WARNING!

To reduce the risk of injury, always unplug tool before attaching or removing accessories or making adjustments. Use only specifically recommended accessories. Others may be hazardous.

Fig. 1

Installing saw blades

This tool uses only T-Shank jig saw blades.

1.Unplug the tool.

2.Push the Quik-Lok tension lever as far as it will go and hold it in position (Fig. 1).

3.Fit the saw blade into the groove in the support roller and push it firmly into the plunger as far as it will go; the lug of the saw blade must be in the plunger.

4.Release the Quik-Lok tension lever and the saw blade is automati- cally held.

5.Check that the saw blade is held firmly; the slot in the plunger will be at an angle to the saw (Fig. 2).

Fig. 2

Slot

Adjusting the shoe (Fig. 3)

The shoe may be tilted up to 45° in either direction and moved forward or backward.

Fig. 3

Shoe screw

1.To set a tilt angle for angle cuts and bevels, loosen the shoe screw, pull the base backward slightly until the retaining lugs are no longer engaged. Tilt to the required preset angle (15°, 30°, or 45°) as read on the tilt angle scale. Push back into the retaining lugs and tighten the shoe screw. If angles other than the presets are re- quired, set the desired angle and tighten the shoe screw without engaging the retaining lugs.

If very exact angles are needed it is recommended that a test cut and subsequent adjustment be made.

2.To move the shoe back for plunge cuts or cuts in corners, loosen the shoe screw and pull the shoe all the way back. The shoe screw will fit into a slot to hold the shoe at 0°.

Using the Shoe Cover

The non-marring shoe cover is used to prevent marring and scratching of the workpiece surface. To attach the shoe cover, hook the front of the cover over the steel shoe. Next, snap the rear of the shoe cover to the steel shoe. Be sure both sides are snapped in place.

When the shoe cover is not needed, remove it by pulling the tabs on rear of the shoe cover outward from the steel shoe. Unhook the front of the shoe cover and remove.

Blade

page 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Operators Manual Electrical Safety General Safety RulesPersonal Safety Tool USE and Care ServiceFunctionaldescription Specific Safety RulesRecommended Minimum Wire Gauge For Extension Cords Guidelines for Using Extension CordsGrounding Extension CordsAdjusting the shoe Fig Tool AssemblyOperation Accessories MaintenanceWarranty RepairsSécuritéélectrique Conservez CES Instructions Aire DE TravailUtilisation ET Entretien DES Outils Sécurité DES PersonnesDescriptionfonctionnelle Règles DE Sécurité ParticulièreMise À LA Terre Avertissement Calibres minimaux recommandés pour Les cordons de rallongeCordons DE Rallonge Directives pour l’emploi des cordons de rallongeRéglage de la semelle Fig Montage DE Loutil AvertissementManiement Avertissement Accessoires Avertissement Maintenance AvertissementGarantie RéparationsSeguridadelectrica USO Y Mantenimiento DE LA Herramienta Guarde Estas Instrucciones Area DE TrabajoSeguridadpersonal ServicioDescripcion Funcional Reglas Especificas DE SeguridadCatálogo Volts Largo de Ca/cd Carrera 6266 120Guías para el uso de cables de extensión Tierra ¡ADVERTENCIAExtensiónes Eléctricas Ajustando la zapata Fig Ensambaje DE LA Herramienta ¡ADVERTENCIAOperacion ¡ADVERTENCIA Accesorios ¡ADVERTENCIA Mantenimiento ¡ADVERTENCIAGarantia ReparacionesUnited States
Top Page Image Contents