Symbology, Fuel Gauge | Milwaukee 48-11-1815, 48-59-1801 specs

FUNCTIONAL DESCRIPTION

MILWAUKEE LITHIUM-ION BATTERY PACK OPERATION

	4	1	1.	Contacts
			1.	Contacts
			2.	Fuel Gauge
			2.	Fuel Gauge
2			3.	Fuel Gauge button
2			4.	Release buttons
			4.	Release buttons
			11	9
	3	6
	4	6
	4
		8
		7
5.	Cord
6.	Nameplate Label			10
7.	Electrical contacts			10
7.	Electrical contacts
8.	Bay
9.	Vents	5

10 . Serial Number (on bottom of charger)

11.Light indicator - when a battery pack is inserted into

the charger, the light will indicate the following situations:

Continuous red light:	Charging
Continuous green light:	Charging is complete
Flashing red light:	Battery pack is too hot or too cold - Charging will begin
	automatically when battery reaches correct charging
	temperature
Flashing red and green light: Damaged or faulty battery pack

Symbology

	Properly Recycle		Underwriters
	Properly Recycle		Laboratories, Inc.,
	Batteries		Laboratories, Inc.,
	Batteries		United States and Canada
			United States and Canada

	Double Insulated		Hertz

	Volts Direct		Amps
	Current		Amps
	Current

	Volts Alternating
	Current

Fuel Gauge

Use the Fuel Gauge to determine the battery pack's remaining run time. Press the Fuel Gauge button to display the lights. The Fuel Gauge will stay lit for two seconds.

Approximate Run

Time Remaining	78-100%
Time Remaining
	55-77%
33-54%
10-32%

Less than 10% if bottom light is ﬂashing

NOTE: If the Fuel Gauge doesn't appear to be working, place the battery pack on the charger and charge as needed.

Unlike other battery pack types, MILWAUKEE Lithium-Ion battery packs deliver fade-free power for their entire run time. The tool will not experience a slow, gradual loss of power as you work. To signal to you that the battery pack is at the end of its run time and needs to be charged, power to the tool will drop quickly. When this happens, remove the tool from the workpiece and charge the battery pack as needed.

NOTE: Immediately after using the battery pack, the Fuel Gauge may display a lower charge than it will if checked a few minutes later. The battery cells "recover" some of their charge after resting.

Battery Pack Protection

To protect itself from damage and extend its life, the battery pack’s intelligent circuit moni- tors current draw and temperature.

In extremely high torque, binding, stalling, and short circuit situations, the battery pack will turn OFF the tool if the current draw becomes too high. In these situations, the tool will "buzz" for about 2 seconds before it turns OFF. To prevent the tool from turning

OFF, immediately reduce pressure on the application or release the trigger. If the tool does turn off, release the trigger to reset. If this happens repeatedly, the battery pack will shut down and need to be placed on the charger to reset.

Under extreme circumstances, the internal temperature of the battery could become too high. If this happens, the battery pack will shut off. Remove the battery pack from the tool and place it on the charger to reset it.

To determine if the battery pack needs to be placed on the charger to be reset, press the fuel gauge button. If the bottom gauge ﬂashes once, the battery must be reset on the charger.

Cold Weather Operation

The MILWAUKEE Lithium-Ion battery pack can be used in temperatures down to -4°F. When the battery pack is very cold, put the battery pack on a tool and use the tool in a light application. It may “buzz” for a short time until it warms up. When the buzzing stops, use the tool normally.

Maintenance and Storage

Do not expose your battery pack or cordless tools to water or rain, or allow them to get wet. This could damage the tool and battery pack. Do not use oil or solvents to clean or lubricate your battery pack. The plastic cas- ing will become brittle and crack, causing a risk of injury.

Store battery packs at room temperature away from moisture. Do not store in damp locations where corrosion of terminals may occur. As with other battery pack types, per- manent capacity loss can result if the pack is stored for long periods of time at high tem- peratures (over 120° F). MILWAUKEE Lith- ium-Ion battery packs maintain their charge during storage longer than other battery pack types. After about six months of storage, charge the pack as normal.