Before You Start
Important Safety
Information
Read all safety information before operating the equipment. Save these instructions
To reduce the risks of fire or explosion, electrical shock and the injury to persons, read and understand all instructions included in this manual. Be familiar with the controls and proper usage of the equipment.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
HAZARD: Injection injury
A high pressure paint stream produced by this equipment can pierce the skin and underlying tissues, leading to serious 
injury and possible amputation. See a physician immediately.
DO NOT TREAT AN INJECTION INJURY AS A SIMPLE CUT! Injection can lead to amputation. See a physician immediately.
The maximum operating range of the gun is 2800
PSI/193 BAR fluid pressure.
PREVENTION:
•NEVER aim the gun at any part of the body.
•Do not aim the gun at, or spray any person or animal.
•NEVER allow any part of the body to touch the fluid stream. DO NOT allow body to touch a leak in the fluid hose.
•NEVER put your hand in front of the gun. Gloves will not provide protection against an injection injury.
•ALWAYS lock the gun trigger, shut the pump off, and release all pressure before servicing, cleaning the tip or guard, changing tip, or leaving unattended.
Pressure will not be released by turning off the motor. The PRIME/SPRAY knob must be turned
to PRIME to relieve the pressure. Refer to the Pressure Relief Procedure (page 7) described in the pump manual.
•ALWAYS keep the tip guard in place while spraying.
The tip guard provides some protection but is mainly a warning device.
•ALWAYS remove the spray tip before flushing or cleaning the system.
•Paint hose can develop leaks from wear, kinking and abuse. A leak can inject material into the skin.
Inspect the hose before each use. Do not use hose to lift or pull equipment.
•NEVER use a spray gun without a working trigger lock and trigger guard in place.
•All accessories must be rated at or above 2800 PSI/193 BAR. This includes spray tips, guns, extensions, and hose.
NOTE TO PHYSICIAN:
Injection into the skin is a traumatic injury. It is important to treat the injury as soon as possible. DO NOT delay treatment to research toxicity. Toxicity is a concern with some coatings injected directly into the blood stream. Consultation with a plastic surgeon or reconstructive hand surgeon may be advisable.
HAZARD: HAZARDOUS VAPORS
Paints, solvents, insecticides, and other materials can be harmful if inhaled or come in
contact with the body. Vapors can
cause severe nausea, fainting, or poisoning.
PREVENTION:
•Use a respirator or mask if vapors can be inhaled. Read all instructions supplied with the mask to be sure it will provide the necessary protection.
•Wear protective eye wear.
•Wear protective clothing as required
by coating manufacturer.
HAZARD: EXPLOSION OR FIRE
Solvent and paint fumes can explode or ignite. Property damage and/or severe injury can occur.
PREVENTION:
•Provide extensive exhaust and fresh air introduction to keep the air within the spray area free from accumulation of flammable vapors. Solvent and paint fumes can explode or ignite.
•Do not spray in a confined area.
•Avoid all ignition sources such as static electric sparks, open flames, pilot lights, electrical appliances, and hot objects. Connecting or disconnecting power cords or working light switches can make sparks. Paint or solvent flowing through the equipment is able to result in static electricity.
•Do not smoke in spray area.
•Fire extinguisher must be present and in good working order.
•Place paint pump in a
•The equipment and objects in and around the spray area must be properly grounded to prevent static sparks.
•Keep area clean and free of paint or solvent containers, rags and other flammable materials.
•Use only conductive or grounded high pressure fluid hose. Gun must be grounded through hose connections.
•Power cord must be connected to a grounded circuit.
•Always flush unit into a separate metal container, at low pump pressure, with spray tip removed. Hold gun firmly against side of container to ground container and prevent static sparks.
•Follow the material and solvent manufacturer’s warnings and instructions. Know the contents of the paints and solvents being sprayed. Read all Material Safety Data Sheets (MSDS) and container labels provided with the paints and solvents. Follow the paint and solvent manufacturer’s safety instructions.
2 | Before You Start • Important Safety Information |
|
English | ||
|
|
|