Craftsman 919.724271 owner manual Assembly, Installation

Page 10

ASSEMBLY

Contents of Carton

1 - Air Compressor

1 - Parts bag containing:

1 - Operator’s Manual

1 - Parts Manual

4 - 5/8” Washers

Tools Required for Assembly

1 - 9/16” socket or open end wrench

Electric drill

Unpacking

1.Remove all packaging.

It may be necessary to brace

or support one side of the outfit when removing the pallet because the air compressor will have a tendency to tip.

2.Remove and discard the (4) screws and washers holding the compressor to the pallet.

3.With the help of another person carefully remove air compressor from pallet and place on a level surface.

INSTALLATION

HOW TO SET UP YOUR UNIT

Location of the Air Compressor

•Locate the air compressor in a clean, dry, and well ventilated area.

•Located the air compressor at least 12" away from the wall or other obstructions that will interfere with the flow of air.

•Locate the air compressor as close to the main power supply as possible to avoid using long lengths of electrical wiring. NOTE: Long lengths of electrical wiring could cause power loss to the motor.

•The air filter must be kept clear of obstructions which could reduce air flow to the air compressor.

Anchoring of the Air

Compressor

Excessive Vibration can weaken the air

tank and cause an explosion. The compressor must be properly mounted.

The air compressor MUST be bolted

to a solid, level surface. Hardware needed:

4 - Concrete anchors

4 - 3/8” Lag screw to fit concrete anchors (not supplied)

4 - 5/8” Washer (found in parts bag) shims (if needed)

1.Place the air compressor on on a solid, level surface.

2.Mark the surface using the holes in the air compressor feet as a template.

3.Drill holes in the surface for the concrete anchors. Install concrete anchors.

3/8” Lag

Screw

(not supplied)

5/8” Washer (supplied)

Shim Under

 

Surface Line

 

 

 

 

Washer

Concrete Anchor

(not supplied)

(not supplied)

3.Line-up holes in surface with holes in air compressor feet.

D25050

10- ENG

Page 9 Page 11
Image 10
Page 9 Page 11
Contents AIR Compressor Sold by Sears Canada, Inc. Toronto, Ont. M5B 2B8Table of Contents Important Safety Instructions Specification ChartSafety Guidelines Definitions Model No 919-724270Hazard Risk of Explosion or FireRisk of Bursting Risk from Flying ObjectsRisk of Electrical Shock Risk to BreathingRisk from Moving Parts Risk of BurnsRisk of Falling Risk of Unsafe Operation Glossary AccessoriesAccessories Duty CycleAssembly InstallationAir Distribution System Wiring InstructionsVoltage and Circuit Protection Risk of ElectricalTypical Compressed AIR Distribution System Description of Operation OperationKnow Your Air Compressor Drain ValveCheck Valve How to StopBefore Starting Pressure Release ValveHow to Start Before Each Start-UpCustomer Responsibilities MaintenanceTo Check Safety Valve To Drain TankInspect Air Lines and Fittings for Leaks Air Filter Inspection and ReplacementAir Compressor Pump Intake and Exhaust Valves MotorNut Outlet Tube Pressure Relief Check Valve Service and AdjustmentsTo Replace or Clean Check Valve Screwdriver Open position nothing is visibleStorage Troubleshooting Problem Cause CorrectionProblem Cause Correction Check wiring connection Table DES Matières Sears Canada, Inc., Toronto, Ont. M5B 2B8Mesures DE Sécurité Définitions Tableau DES SpécificationsConsignes DE Sécurité Importantes Risque D’EXPLOSION OU D’INCENDIE RisqueRisque D’ÉCLATEMENT Risque DE Projection D’OBJETSRisque DE Choc Électrique Risque PAR InhalationRisque Relié AUX Pièces Mobiles Risque DE BrûluresRisque DE Chute Risque Dune Utilisation Dangereuse Accessoires AccessoiresCycle DE Service LexiqueAssemblage Tension et protection des circuits Directives de câblageDirectives DE Mise À LA Terre Système de distribution dairSystème DE Distribution Dair Typique Familiarisez-vous avec votre compresseur dair UtilisationDescription du fonctionnement Arrêt de lappareil Utilisation de lappareilAvant le démarrage Procédures de rodageAvant chaque mise en marche Mise en marcheVérification de la soupape de sûreté EntretienResponsabilités du client Vidange du réservoirMoteur Filtre à air Inspection et remplacementFiltre à air Remplacement ou nettoyage de la soupape de retenue Entretien ET RéglagesRangement Serrer DépannageProblème Cause Correction Peut éclater ou exploserCognements Pas Surcharges déclenché D25050 ENG ENG D25050 Get it fixed, at your home or ours

919.724271 specifications

The Craftsman 919.724271 is a highly regarded air compressor that caters to both hobbyists and professionals. Known for its reliable performance and user-friendly features, this model stands out in the extensive Craftsman lineup for its versatility and robustness.

One of the key features of the Craftsman 919.724271 is its powerful motor. Equipped with a 1.5 horsepower, this motor can deliver a maximum pressure of 135 PSI, making it suitable for various applications including inflating tires, powering pneumatic tools, and handling light automotive repairs. The compressor has a 6-gallon tank that offers sufficient air supply, allowing for prolonged use without constant recharging.

The design of the 919.724271 emphasizes portability and ease of use. Weighing in at a manageable 30 pounds, it includes a convenient handle and rubberized wheels, making it easy to move from one job site to another. Its compact size allows for easy storage in a garage or workshop, making it an ideal choice for those with limited space.

Another significant characteristic of the Craftsman 919.724271 is its oil-free pump system. This technology not only reduces maintenance needs, but it also minimizes the risk of oil contamination in your projects. Users can enjoy the convenience of a cleaner operation and hassle-free upkeep, allowing them to focus on their work without worrying about oil changes or cleanups.

The compressor is also designed with a quick recovery time, thanks to its efficient power management. Users can expect fast recharging between uses, making it ideal for tasks that require a continuous airflow. The easy-to-read pressure gauge and regulator allow for precise control of air pressure, which is essential for tasks that require specific pressure settings.

Safety is prioritized in the Craftsman 919.724271, which incorporates thermal overload protection. This feature ensures that the compressor does not overheat during extended use, prolonging its lifespan and maintaining performance.

Overall, the Craftsman 919.724271 is a well-rounded air compressor that meets the demands of diverse users. Its compelling combination of power, portability, and innovative design makes it an excellent addition to any toolkit, whether for light DIY projects or professional use. With the reliability associated with the Craftsman brand, users can find confidence in the 919.724271 to deliver efficient and effective performance every time.
Top Page Image Contents