Kawasaki 843327 instruction manual Safety of operation, Safety Rules for Circular Saws

Page 5

Lower guard should be retracted manually only for special cuts such as “Pocket Cuts” and “Compound Cuts.” Raise lower guard by Retracting Handle. As soon as the blade enters the material, lower guard must be released. For all other sawing, the lower guard should operate automatically.

Always observe that the lower guard is covering the blade before placing saw down on bench or floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after the switch is released.

NEVER hold piece being cut in your hands or across your leg. It is important to support the work properly to minimize body exposure, blade binding, or loss of con- trol.

Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of the tool “live” and shock the operator.

When ripping always use a rip fence or straight edge guide. This improves the accuracy of the cut and reduces the chance for blade binding.

Always use blades with correct size and shape (diamond vs. round) arbor holes. Blades that do not match the mounting hardware of the saw will run eccentrically, causing loss of control.

Never use damaged or incorrect blade washers or bolts. The blade washers and bolts were specifically designed for your saw, for optimum performance

and safety of operation.

SAFETY RULES FOR CIRCULAR SAWS

NEVER assume the blade has stopped just because the trigger has been released. Blades may continue moving even after the motor stops.

Always wear safety goggles or eye protection when using this tool. Use a dust mask or respirator for applications which generate dust. This saw may throw up debris that could lodge in the eyes causing severe pain or injury.

Inspect the bolts and blade washers before each use. Damaged or incorrect

bolts or blade washers can cause injury.

When using the Circular Saw, always maintain a firm grip on the tool with both hands. Never put your hands or feet in the cutting area. Do not grasp the tool or place your hands too close to the blade. Keep your hands well away

7

from the blade. Never reach underneath the tool while the blade is in motion.

Do not use your legs or feet to stabilize the work piece.

Keep the handle of the Circular Saw dry, clean and free from oil and grease.

Do not run the Circular Saw while carrying it at your side. A moving blade

could cause serious personal injury.

Disconnect the power cord plug from the power source before making any assembly adjustments, changing accessories, performing any inspection, maintenance or cleaning procedures. Such preventive safety measures reduce the risk of starting the tool accidentally which could cause serious personal injury.

Be extra careful when cutting in high or hard-to-reach locations. Avoid saw- ing overhead. Be on the lookout for hidden wires and falling debris.

Do not use the Circular Saw if it has been damaged, left outdoors in the rain, snow, wet or damp environments, or immersed in liquid.

Maintain labels and nameplates on the Circular Saw. These carry important information. If unreadable or missing, contact Alltrade for a replacement.

CAUSES AND PREVENTION OF KICKBACK

Kickback is a sudden reaction to a pinched, bound, or misaligned saw blade, caus- ing an uncontrolled saw to lift up and out of the work piece toward the operator.

When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator.

If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the metal causing the blade to climb out of the kerf and jump back toward the operator.

Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below:

Maintain a firm grip on the saw and position your body and arm in a way that allows you to resist KICKBACK forces. KICKBACK forces can be controlled by the operator, if proper precautions are taken.

When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or KICKBACK may occur.

Investigate and take corrective actions to eliminate the cause of blade binding.

Image 5
Contents 4 Circular SAW General Safety Rules for ALL Electric Power Tools Table of ContentsRecognize Safety SYMBOLS, Words and Labels CongratulationsWork Area Important SafeguardsElectrical Safety Service Personal SafetySpecific Safety Rules AND/OR Symbols Tool USE and CareSafety Rules for Circular Saws Safety of operationBolts or blade washers can cause injury Could cause serious personal injurySymbol Name Explanation SymbolsAccessories Functional DescriptionCutting Depth Adjustment AssemblyAttaching / Removing Blade Mounting the RIP FenceLaser Safety Bevel Angle AdjustmentOperation Accessible Fields Laser GuideOperating the Laser Operating the on / OFF SwitchOperating the Circular SAW General CuttingCutting Thin or Corrugated Materials Cutting Materials Thicker than 1/4 3/4 Maximum ThicknessCutting Large Sheets Pocket CuttingLaser Maintenance Maintenance and CleaningAccessories SpecificationsOther Consumer DO-IT-YOURSELF DIY Tools Year Limited WarrantyCircular Saws Tools Angle Grinders Commercial or Rental PurposeWarranty Disclaimers

843327 specifications

The Kawasaki 843327 is an exceptional piece of machinery that has gained recognition for its reliability and robust performance in various applications. Engineered for both durability and efficiency, it is primarily designed for a range of agricultural and industrial tasks, making it a versatile addition to any operation.

One of the standout features of the Kawasaki 843327 is its powerful engine, which offers impressive horsepower and torque. This strong engine allows for smooth operation, even when faced with demanding workloads. The unit operates with remarkable fuel efficiency, minimizing downtime for refueling and maximizing productivity. This balance of power and efficiency is particularly beneficial for users who require sustained performance throughout their workday.

Technology plays a pivotal role in the design of the Kawasaki 843327. The machine is equipped with advanced controls that enhance user experience and operational effectiveness. The intuitive interface allows for easy manipulation of various functions, making it accessible for operators of varying skill levels. Additionally, it incorporates precision engineering, ensuring that all components work harmoniously to deliver consistent results in any environment.

Durability is another hallmark of the Kawasaki 843327. Constructed with high-quality materials, this unit is designed to withstand the rigors of heavy use. The robust build helps prevent common wear and tear, significantly extending the lifespan of the machinery. Furthermore, it features protective casing and components that shield vital parts from environmental damage, ensuring long-term reliability in harsh conditions.

Another key characteristic is the machine's adaptability. The Kawasaki 843327 can handle a range of attachments and implements, enhancing its multifunctional capabilities. This adaptability makes it suitable for various tasks, such as tilling, hauling, and plowing, which are common in agricultural settings, as well as in construction and landscaping projects.

Regular maintenance is simplified with the Kawasaki 843327, as it is designed for easy access to vital components. Routine checks and service can be executed quickly and efficiently, which helps in maintaining optimal performance and reducing unnecessary downtime.

In summary, the Kawasaki 843327 is a power and efficiency-driven machine that excels in various environments. With advanced technology, robust construction, and versatile adaptability, it remains a top choice for professionals seeking a reliable partner for their toughest tasks.