Pelco C1498M-B operation manual Specifications, Back BOX Electronic Assembly Removal

Page 19

8.If the red power LED is lit, turn off power.

a.Open the door to the interconnect circuit board and check that all connectors are fully seated.

b.Make sure the wiring is correct between the unit and controller.

c.Close the door. Check the switch settings on the dome drive (refer to Tables A, B, and C) and reinstall the dome drive.

d.Turn on power. If the unit still does not operate, turn off power and replace the dome drive with a unit that is good, if you have a spare. Check the switch settings on the substitute dome drive before installing it. If you do not have a spare, return the dome drive to the factory. Also return the back box electronic assembly. Refer to the Back Box Electronic Assembly Removal section.

e.If you substituted a dome drive, turn on power. If the unit operates, the original dome drive is bad. Return it to the factory. If the unit still does not operate, then the interconnect board is bad. Return the back box electronic assembly to the factory. Refer to the Back Box Electronic Assembly Removal section.

BACK BOX ELECTRONIC ASSEMBLY REMOVAL

1.Turn off power.

2.Open the interconnect door and disconnect all wiring to the back box.

3.Use an 11/32 socket driver to remove the three 8-32 washers and nuts that hold the electronic assembly to the back box. When you remove the screws the interconnect back box receptacle will drop down. You may have to move the open interconnect door past 90 degrees vertical toward the side of the back box to release the door from the built-in grounding strip (and free the interconnect back box receptacle).

4.Remove the interconnect back box receptacle with the electronic components from the back box.

SPECIFICATIONS

MECHANICAL

 

 

Pan Movement:

360° continuous pan rotation

Vertical Tilt:

Unobstructed +2° to -92°

Manual Pan Speed:

0.5°-80°/sec manual operation, 150°/sec turbo

Manual Tilt Speed:

0.5°-40°/sec

Preset Speeds:

Pan

250°/sec

 

Tilt

200°/sec

Fixed-Speed Controller: Pan

30°/sec

 

Tilt

12°/sec

CAMERA

 

 

Signal Format:

NTSC (Spectra Lite™ model DD5TAC)

 

PAL (Spectra Lite™ model DD5TAC-X)

Scanning System:

2:1 interlace

Image Sensor:

1/4-inch interline transfer

Effective Pixels:

NTSC

510 (H) x 492 (V)

 

PAL

500 (H) x 582 (V)

Resolution:

NTSC

350 TV lines

 

PAL

350 TV lines

Lens

 

 

Minimum f-stop:

F/1.6

 

Focal Length:

3.9 mm to 63 mm optical

Zoom Ratio:

16X optical zoom

Horizontal Angle

44° (at 3.9 mm wide zoom), 3° (at 63 mm telephoto zoom)

of View:

MTBF:

>1 million cycles at room temperature (zoom, focus, iris)

Focus:

Automatic with manual override and preset capability

Pelco Manual C1498M-B (7/99)

19

Image 19
Contents Listed Contents Models Important Safeguards and WarningsInstallation DescriptionTable B. Switch Settings for SW2 P-Type Control Table C. Switch Settings for SW2 D-Type Control OFF 113 169 Operation POWER-UP DisplayScan Speed Preset FunctionsPAN and Tilt Functions Auto FlipPark Main Menu AccessProgramming the Spectra Lite CM9760 Reset CameraBacklight Compensation CM9750Auto Iris GAIN/AGCShutter Speed AUTO-FOCUS ModeWhite Balance SharpnessLine Synchronization POWER-UP Mode Park Time Minutes Limit StopsSymptom Unit or fan does not operate TroubleshootingBack BOX Electronic Assembly Removal SpecificationsRegulatory Notices Warranty and Return Information