Pelco C1498M-B operation manual Warranty and Return Information, Regulatory Notices

Page 20

Sensitivity:

1 lux at f1.6 at signal level of 40 IRE, gain high (AGC on)

Signal Process:

DSP-3R

Sync System:

AC line lock

White Balance:

Automatic with manual override*

Shutter Speed:

Automatic (electronic iris)/manual

 

NTSC

1/60 – 1/10,000*

 

PAL

1/50 – 1/10,000*

Iris Control:

Automatic with manual override*

Gain Control:

Automatic with manual override*

Video Output:

.714 V ±.07 V (100 IRE ±10 IRE)

Signal to Noise:

>46 dB

 

*Manual control over camera setup functions depends on the head end and is not available on all control models.

(Design and product specifications subject to change without notice.)

REGULATORY NOTICES

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reason- able protection against harmful interference when the equipment is operated in a commer- cial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below:

Three years on Genex™ Series (multiplexers, server, and keyboard).

Two years on all standard motorized and fixed focal length lenses.

Two years on Esprit™, Legacy®, Intercept®, PV1000 Series, CM6700/ CM8500/CM9500/CM9750/CM9760 Matrix, Spectra®, DF5 Series and DF8 Fixed Dome products.

Two years on WW5700 series window wiper (excluding wiper blades).

Two years on cameras.

Six months on all pan and tilts, scanners or preset lenses used in continu- ous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, al- teration, normal wear, or accident are not covered under this warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringe- ment of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (includ- ing loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information:

1.Model and serial number

2.Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3.Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explana- tion with the product when returned.

Ship freight prepaid to:

Pelco

 

300 West Pontiac Way

 

Clovis, CA 93612-5699

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization num- ber (CA number if returned for credit, and RA number if returned for repair). Goods returned for repair or credit should be clearly identified with the assigned CA/RA number and freight should be prepaid. All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Ship freight prepaid to:

Pelco

 

300 West Pontiac Way

 

Clovis, CA 93612-5699

REVISION HISTORY

Manual #

Date

Comments

 

C1498M

2/99

Original version.

 

 

3/99

Removed reference to line synchronization. Added material on auto iris. Added FCC notice.

C1498M-A

7/99

Revised the preset tilt speed from 100 to 200 degrees/second. Added model number and specifications for a PAL camera.

 

 

Revised Troubleshooting section. Revised manual to new format.

 

C1498M-B

7/99

Changed camera zoom from 12X to 16X. Added line sync and auto focus features. Removed auto iris peak and auto sharpness

 

 

options. Replaced R-B and M-G white balance options with white balance hue option. Revised camera specifications.

® Pelco and the Pelco logo are registered trademarks of Pelco.

© Copyright 1999, Pelco. All rights reserved.

20

Pelco Manual C1498M-B (7/99)

Image 20
Contents Listed Contents Important Safeguards and Warnings InstallationDescription ModelsTable B. Switch Settings for SW2 P-Type Control Table C. Switch Settings for SW2 D-Type Control OFF 113 169 POWER-UP Display OperationPreset Functions PAN and Tilt FunctionsAuto Flip Scan SpeedProgramming the Spectra Lite Main Menu AccessPark Reset Camera Backlight CompensationCM9750 CM9760GAIN/AGC Auto IrisAUTO-FOCUS Mode Shutter SpeedLine Synchronization SharpnessWhite Balance POWER-UP Mode Limit Stops Park Time MinutesTroubleshooting Symptom Unit or fan does not operateSpecifications Back BOX Electronic Assembly RemovalWarranty and Return Information Regulatory Notices